background image

11(14)

7.2.

 

The rubber lip plate and the sweeping plate

The operation of the spreaders is based on the two rubber plates leaning against the spreading axle, which
makes  controlled  spreading  of  the  material  possible.  If  the  spreading  result  is  uneven  after  cleaning  and
adjusting  the  equipment, the  condition  of the  rubber  plates,  shown  in  the  figures  below,  must  be  checked.
The edge of the plates should be even, and they should be adjusted to lean lightly against the axle. Please
contact your nearest AVANT service if needed.

7.3.

 

Checking and adjusting the chain drive

The  roller  chain  transmission  between  the  hydraulic  motor  and  the  mixing  and  spreading  axles  should  be
inspected whenever the protective cover is opened for lubricating the bearings. Clean the chain housing and
lubricate the chain with suitable type of oil. The tightness of the chain can be checked by pushing the chain
between  the  sprockets  with  moderate  force.  The  clearance  of  the  chain  should  be  about  0.5  –  1  cm.  If
necessary, the chain is adjusted by moving the hydraulic motor until the chain is at correct tightness. Tighten
any loosened bolts and fit the protective cover back to its place.

8.

 

Warranty terms

Avant  Tecno  Oy  grants  a  warranty  of  one  year  (12  months)  from  the  date  of  purchase  for  the  attachment  it
manufactures.

The warranty covers repair costs as follows:

 

Work costs are covered, if the repair is not performed at the factory.

 

The factory replaces any defective components or consumables.

The factory may reimburse the price of components purchased by the customer in special cases that have been agreed in
advance.

The warranty does not cover:

 

Normal maintenance work or parts and consumables required for it.

 

Damages caused by unusual operating conditions or ways of use, negligence, structural changes made without the
consent of Avant Tecno Oy, use of non-original parts or lack of maintenance.

 

Consequences of a defect, such as interruption of work or other possible additional damages.

 

Travel and/or freight costs caused by the repair.

Spreader models A21114 and A2947
Rubber plates and spreading shaft

Содержание A21114















Отзывы: