Avalue Technology SID-15V Скачать руководство пользователя страница 11

Quick  Reference  Guide 

SID-15V  Quick  Reference  Guide    11 

 

1.5 Battery Specifications (Optional)   

1.5.1 

General Specifications 

 

General 

Battery Model 

Number 

ACC-BAT-3S1P-01R 

Battery Cell Type 

Li-Ion Rechargeable Cell 

Nominal Voltage 

AVG. 10.8V 

Charging Voltage 

MAX. 12.6V 

Typical Capacity 

2400 mAh 25ºC±2ºC 

Minimum Capacity 

2215 mAh at 25ºC, by 0.2C 443 mA discharge 

Standard Charging 

12.6 V / CC: 0.5C, 1106 mA at 25ºC ± 2ºC 

Terminal charge condition: <117 mA 

Maximum Charging 

12.6 V / CC: 0.9C, 2000 mA at 25ºC ± 2ºC 

Terminal charge condition: <117 mA 

Charge rates >0.86 C are NOT recommended. 

Pre-Charge Current 

128 mA (When cell voltage under 3.0V or temperature under 10 ºC) 

Standard Continuous 

Discharge Current 

0.2 C 443 mA   

Continuous discharging to 8.25 V 

Maximum 

Continuous 

Discharge Current 

1.355 C 3000 mA   

Continuous discharging to 8.25 V 

Charge Termination 

Condition 

When  the  pack  voltage  is  12.6  V,  and  the  charge  current  is  less  than  or 

equal to 117 mA the charging should be terminated. 

Relative State Of Charge = 100 % 

When  the  Relative  State  Of  Charge  is  under  95%,  the  pack  can  re-start 

charging. 

Discharge 

Termination 

Condition 

When pack voltage is less than or equal to 8.25 V, the discharging should be 

terminated. 

Operating 

Temperature 

Charge: 0 ºC~ 45 ºC, 85%RH Max 

Discharge -10 ºC~ 60 ºC, 85%RH Max 

Storage Temperature 

If  the  battery  packs  are  subject  to  storage  for  such  a  long  term,  it  is 

recommended to recharge the battery pack periodically, every two-months. 

 

1 Month -20~60 ºC, 85 %RH Max 

3 Months -20~45 ºC, 85 %RH Max 

1 Year -20~20 ºC, 85 %RH Max 

Содержание SID-15V


























Отзывы: