background image

Avago Technologies

- 7 -

LSI SAS 9207-8i PCI Express to 6Gb/s SAS HBA User Guide 
October 2014

 LSI SAS 9207-8i HBA Certifications and Safety Characteristics 

6

LSI SAS 9207-8i HBA Certifications and Safety Characteristics

The LSI SAS 9207-8i HBA meets or exceeds the requirements of UL flammability rating 94V-0. Each bare board is 

marked with the supplier’s name or trademark, type, and UL flammability rating. Because these boards are installed in 
a PCIe bus slot, all voltages are less than the SELV 42.4-V limit.

The design and implementation of the LSI SAS 9207-8i HBA minimizes electromagnetic emissions, susceptibility to 
radio frequency energy, and the effects of electrostatic discharge.

The LSI SAS 9207-8i HBA meets the following integrated electromagnetic interference (EMI) compliance labels:

CE mark

CISPR Class B

C-Tick mark

Canadian Compliance Statement

FCC Class B, marked with the FCC Self-Certification logo

Japan VCCI

Korean KCC

Taiwan BSMI

The LSI SAS 9207-8i HBA meets the following environmental directives:

RoHS

WEEE

7

Hardware Installation

The installation instructions for the LSI SAS 9207-8i HBA follow.

1.

Unpack the HBA, and inspect it for damage. 

Unpack the HBA in a static-free environment. Remove the HBA 

from the antistatic bag, and carefully inspect it for damage. If you notice any damage contact LSI or your reseller 
support representative.

ATTENTION

Make a backup of your data before changing your system 
configuration to avoid the risk of data

 loss.

2.

Prepare the computer.

 Turn off the computer, and disconnect the power cord from the rear of the power supply.

CAUTION

Disconnect the computer from the power supply and from any 
networks before you install the HBA, or you risk damaging the system 
or electrical shock.

3.

Remove the cover from the chassis.

 

4.

Replace the mounting bracket (system dependent).

 If required for your system, replace the full-height 

mounting bracket that ships on the LSI SAS 9207-8i HBA with the low-profile bracket supplied. Save and reuse the 
two screws that attach the long bracket to attach the short bracket.

5.

Insert the HBA in an available PCIe slot.

 Locate an empty x8 PCIe slot. Remove the blank bracket panel on the 

rear of the computer that aligns with the empty PCIe slot. Save the bracket screw, if applicable.

Align the HBA to a PCIe slot. Press down gently, but firmly, to correctly seat the HBA in the slot. The following 
figure shows how to insert the HBA in a PCIe slot.

Содержание SAS 9207-8i











Отзывы: