background image

PAGE 3

Help: 888-426-5001

QualityWaterForLess.com

    ›ta B l e   o F   C o n t e n t s

Page 2 

Meter Control Valve Ports and Programming Reference 

(Click to Jump to Page)

Page 3 

Table of Contents

Page 4 

Calculating your Hardness Level, and Salt Grid Table

Page 5 

Tank Size, Salt Setting, and Salt Grid Table

Page 6 

Pre-Installation and Tank Placement

Page 7 

Filling the Tank and Installing the Autotrol 255/760 Valve onto the Tank

Page 8 

Installing the Bypass and Drain Line onto the Valve

Page 9 

Plumbing the System into your Home and Making the Brine Tank Connection

›PR e FaC e

Thank you for your purchase of a new water softener with Autotrol 255/760 Meter Control Valve from 
QualityWaterForLess.com! We have put together these instructions as reference and to be used as gen-
eral installation guidelines. 

It is always recommended that a licensed plumber perform all installa-

tion work according to all local codes.

 We at QualityWaterForLess.com cannot assume responsibili-

ty for improper installation, application, or injury or damage as a result of improper installation.

Page 11 

Programming the Autotrol 255/760 Valve

Page 13 

Initial System Start-Up

Содержание 255/760














Отзывы: