Press and hold
F
button of LCD remote until 2 beeps sound , release and re-press
F
button again
the
LCD remote will show
“CH 3” icon flash
, then press
button
to activate channel 3 function.
T.
CHANNEL 4 TIMER CONTROL OUTPUT
Press the transmitter
and
buttons at the same time to active Channel 4 function.
or
Press and hold
F
button of LCD remote until 2 beeps sound , release and re-press
F
button twice
the
LCD remote will show
“CH 4” icon flash
, then press
button
to activate channel 4 function.
Channel 4 is user-programmable timer output. You may program the built-in timer to send a ground signal for any time
duration from 1 second to 120 seconds. For instance, this timer output may be used to turn on the headlight, power
window or sunroof. (Factory defaults setting at momentary output.)
U. POWER SAVER MODE (Default OFF)
Under Menu mode press
button while
“POWER SAVE”
icon flash, press
button Power save ON, while
the power save mode, the LCD remote transceiver use “0” current to save the battery power. Press
button
Power save OFF
Exit: Press any button of the LCD remote transmitter to exit “Power Save Mode”.
V. POWER ON MEMONRY:
This security system is equipped with circuitry that will allow the unit to remember its alarm state if the
power is lost and then reconnected.
W. SECOND VEHICLE SECURITY OPERATION:
Your 5-button remote transmitter can be utilized to control a second vehicle security system, To program the remote
control transmitter to a second vehicle, follow the instructions for Transmitter programming.
* For the standard transmitter (
II
) is shift button.
1. Prior to pushing any button on the transmitter. Press the Select
II
button first on the transmitter.
2. Once
II
button is pressed the LED on the transmitter will illuminate for 3 seconds to indicate the second transmitter
pin code has built-in.
3.
While the LED is illuminated, press any button on the remote control transmitter to control a second vehicle security
system.
** For LCD transceiver – 2
nd
car operation :
a. Press and hold
F
button of LCD remote for 1 second until 2 beeps sound, then release the
F
button.
b. The text
will flash on the LCD screen, press
button to enter the menu.
c. Press
or button to move up or down in the menu, find CAR SELECT on the menu.
d. Press
button to select the option you would like to adjust CAR 1 or CAR 2 for further operation.
X. CHECK VEHICLE’S VOLTAGE:
Press
button while
VOLTAGE
icon flash (see Table 3); the vehicle’s voltage will be shown
on the LCD screen. Please note that this data is for your reference only. Please check the exact data on
vehicle.
REMOTE START OPERATION:
A. TO REMOTE START THE VEHICLE:
When you want to start your vehicle,
1. Press
button once on the transmitter.
2. The parking light will activate to indicate the remote start received the signal.
3. The engine will start in approximately 5 seconds.
4. Once the engine is running, after couple seconds the parking lights will turn on and the climate controls
will activate and adjust the vehicle’s interior temperature to your preset setting. (While the vehicle is
running, the “minutes” digit on the LCD screen will flash and the will indicate count down timer based on
the 5, 10, 20 or 30 minute run time set up by your installation center.)
5. The vehicle will run for a programmable 5 to 30 minute cycle before shutting down. (When the unit
shuts off the count down timer will turn off and the transmitter will play a melody.)
NOTE: The Remote Start Unit will not start the vehicle if any one of the following conditions exists:
1. The hood is opened.
2. The brake pedal is pressed.
3. The optional remote start enable toggle is switched to the “OFF” position. (If installed)
4. The gear selector is in any gear other then “PARK” or “NEUTRAL”
SAFE START (Child safety mode)
Factory default is set to press the
button once on the transmitter to start the vehicle. You can program this feature
to eliminate an accidental remote start:
1. The user presses the transmitter
buttons twice within 3 seconds to start the vehicle. or
2. The user presses the transmitter
and
buttons at the same time to start the vehicle.
NOTE: Contact your installing dealer to activate this feature.
9
