15A Fuse
5. Red Wire: +12V To Constant Battery Source
4. Brown Wire: Positive output To
3. Black Wire: Ground to Vehicle FRAME
2. White Wire: Parking Light Relay Output
1. Red / White Wire: Parking Light Relay input
Siren
Transmitter Programming
Note:
This mode will only retain the last 4 remote transmitters programmed. If the transmitter
memory is exceeded, the security system will start deleting transmitters from memory in
chronological order.
1. Turn the Ignition 'switch ‘
OFF/ON’ 3 TIMES
and stay in
ON position
.
“Within 15 seconds”.
2. Push the Valet switch
2 times
and hold it on the
2
nd
push until a long chirp is heard then
release the valet switch. You are now in the Transmitter programming mode.
3. Press and hold any button of the transmitter until the siren responds with a confirming chirp,
indicating the signal has been stored into memory.
4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for
each transmitter.
Exit:
Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 long chirps & 3 parking light
flashes will confirm exit.
355A
5 PIN WIRE HARNESS
This manual was written September 1, 2015
©2015 Varad International, Inc. All rights reserved.
GI-S346
* Starter Kill relay optional
ALARM FEATURE “I” PROGRAMMING:
1
Turn the Ignition 'switch ‘ON/OFF’
3
TIMES and stay in
OFF
position.
2
Push the Valet switch
3
times and hold in on the
3rd
push. When a long chirp is heard, release the
valet switch. You are now in the Alarm feature
‘I’
programming mode.
3
Press the transmitter button corresponding to the feature you want to program.
a.
The factory default settings is always [1] LED flash, [1] chirp.
4
Depress the transmitter button again to change the feature. Simply keep pressing the transmitter
button again until the module advances to your desired setting.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulses
Three Chirps
/
LED three
pulses
Four Chirps /
LED four
pulses
1
Active arming
Passive arming
without passive
door locking
Passive
arming with
passive door
locking.
2
Automatic Rearm off
Automatic Rearm
on
3
Instant Door Ajar
error chirp
45 seconds delay
Door Ajar error
chirp.
4
Siren Confirmation
chirp on only
All Confirmation
chirps On
Horn
Confirmation
chirp on only
All
Confirmation
chirps off
5
+
White wire=
Dome Light Output
White wire=
4
th
Channel
Momentary
White =
4
th
channel
Latched
6
+
Lock/Arm &
Unlock/Disarm
Confirmation Chirps
Lock/Arm
Confirmation
Chirp Only
7.
+
ALARM with
Keyless Entry
Keyless Entry
ONLY
8.
+
Car Jacking
feature Off
Car Jacking
feature On
ALARM FEATURE “B” PROGRAMMING:
1
Turn the Ignition 'switch ‘ON/OFF’
3
TIMES and stay in
OFF
position.
2
Push the Valet switch
5
times and hold in on the
5
th
push. When a long chirp is heard, release the
valet switch. You are now in the Alarm feature
‘B’
programming mode.
3
Press the transmitter button corresponding to the feature you want to program.
Press
Transmitter
Button
One Chirp / LED
one pulse
Factory Default
Setting
Two Chirps / LED
two pulses
Three Chirps / LED
three pulses
Four Chirps /
LED four
pulses
1
Pathway
illumination feature
“off”
Parking light turns
“on” for 30- second
upon an unlock
signal
Parking light turns
“on” for 30- second
upon an unlock signal
& 10-second upon a
lock signal.
2
Ignition controlled
door locks &
unlocks
Ignition controlled
door locks only
Ignition controlled
door unlocks only
Without ignition
controlled door
locks & unlocks
3
0.8-second Door
lock pulses.
3.5-second Door
lock pulse.
Double pulse unlock
Comfort feature
4
3
rd
Channel Pulsed
3
rd
Channel
Momentary
5
+
Button =
Silent Arm/Disarm
Button = 4
th
Channel Aux.
6
+
Gray Wire = Trunk
(Channel 3) Output
Gray Wire = Two
Step Door Unlock
Output
7.
+
Horn chirp Duration
Standard
Horn chirp Duration
50 mS
Horn chirp Duration
30 mS
Horn chirp
duration
10 mS
Exit:
Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm exit.
SHOCK SENSOR ADJUSTMENT
1. Turn the Ignition switch ‘ON/OFF’
3
TIMES and stay in
OFF
position.
2. Push the Valet switch
7
times holding in on the 7th push. Three chirps with a long chirp will be heard. Release the valet
switch. You are now in the Alarm feature ‘Shock Sensor’ programming mode.
3. Press and hold
button for 2 seconds. One long siren chirp will indicate the unit is ready to accept adjustments of the
shock sensor.
4. Press
button on the transmitter once. This will
decrease
sensitivity level by one. Each time the button is pushed and a
decrease is made the siren/horn chirp will respond with [1] chirp. Two chirps indicate the minimum sensitivity. Warn away &
full trigger will be deleted when minimum sensitivity is selected
5. Press
button on the transmitter once. This will increase sensitivity level by one. Each time an increase is made the
siren/horn chirp will respond with [1] chirp. Two chirps indicate the maximum sensitivity.
6. Hit the bumper or strong metal part of the vehicle to test the threshold level of the sensor.
a). Activate the warn-away (first stage the shock sensor), the siren will emit a short chirp.
b). Activate the full alarm (second stage the shock sensor), the siren will emit a long chirp.
7. When you are satisfied with the setting, press the
button to lock in the adjustment. One long siren chirp will indicate the
unit has locked in the adjustment.
Note: If 30 seconds of inactivity expires or you turn ON the ignition during of above steps, the unit will exit the program mode
and return to the disarmed mode. Three long chirps will confirm exit.
8 PIN CONNECTOR WIRE HARNESS:
355A
INSTALLATION MANUAL
Varad International, Inc.
5349 Zambrano Street,
Commerce,CA 90040
www.varad.com
