-|Transparent Guide|-
Product Components
•
Sensor: ADS-SHP (1 set - emitter and receiver)
• Fixing bolt for the controller (M4×20) × 2
Sold Separately
•
Mounting bracket: ADS-SB12 (one push method)
•
Mounting bracket: ADS-SB10 (screw method)
•
Sensor: ADS-SHP (1 set - emitter and receiver)
•
Controller: ADS-SEC
Recommended Installation for the Sensor
1. Refer to the below and drill the holes on the side pillars of the auto door
for the installation.
•
Check the mounting holes of the head of the emitter and receiver are in parallel for the
optical axes
•
Grind around the mounting holes drilled smoothly.
It may hurt by sharp parts and cause malfunction by the inclined sensor head.
One push method
Screw method
Using
the bracket
Through hole for sensor head
Ø 13 to 14 mm
Fixing screw hole for bracket
M4 Tap or Ø 3 mm
Not using
the bracket
Mounting hole for sensor head
Ø 12.2
±0.1
mm
M10 × 0.75 mm
Panel thickness for sensor head
1.5
±0.5
mm
1.5
±0.5
mm
2. Mount the sensor heads to the mounting holes.
•
It may cause malfunction because the sensitivity setting is not available as the optical
axes are not matched if the sensor body is inclined.
•
Check the damage such as scratches or pollutant on the lens of the sensor head.
It may cause malfunction in the condition of interrupted light or lack of sensitivity by
dust.
•
Be sure to use the mounting brackets of the one push method for the sensor with the
head holder and nuts. In the one push method, check the nuts are fixed on the sensor
body tightly.
Install the sensor with no gap between the nut and the side of the door or panel.
•
Be sure to use the mounting brackets of the screw method for the sensor without the
head holder and nuts.
Install the sensor with no gap between the panel and the sensor.
One push method
Screw method
Using
the bracket
Install the sensor head to the bracket
first and fix the bracket to the desired
place by the screws.
Remove the nut and head holder from
the sensor head first. Install the sensor
head to the bracket and fix the bracket
on the side pillar of the door by the
screws.
Through hole for
sensor head
: Ø 13 to 14 mm
M4 flat
head screw
Bracket
Head holder
Nut
Through hole for
sensor head
: Ø 13 to 14 mm
Screw hole:
M4 Tap or
Ø 3.5 mm
Bracket
①
②
Not using
the bracket
Put the sensor head into the mounting hole.
■ Cautions during installation
•
The rated sensing distance is max. 10 m (A).
Install the sensors within the rated sensing distance.
•
Install the sensor with more than 50 cm (B) gap from
the bottom and ceiling. It may cause malfunction by
reflected beams from the surface of the bottom and
ceiling.
•
Do not put obstacles between the emitter and
receiver. Otherwise, it may result in malfunction
B
B
A
[Fig. 1]
Cautions during Installation
•
Install the unit correctly with the usage environment, location, and the designated
specifications.
•
When installing over the two door sensors closely, it may result in malfunction due to
mutual interference. Do not change the position of the head of emitter and receiver.
Keep the installation distance between the two heads more than 50 cm.
•
This product is for indoor only.
Avoid the place where the receiver is exposed to direct sunlight, or the ambient
illumination is in over the rated value.
•
Do NOT impacts with a hard object or excessive bending of the wire lead-out. It may
cause damage the water resistance
Recommended Installation for the Controller
1. Refer to the figure at the right side and adjust
the length of wires.
•
Cut off the wires as much as your need and take off
the cover of them. Twist the end of the wires shown
in the figure, and connect to the controller.
It is easy to connect if soldering the end of the wires.
•
Be sure to connect the wires in power OFF.
•
Follow the figure when cutting off the wires of the
sensor head. If taking off the cover too much, it may
cause damage to this product as the end of both
wires are in contact with each other.
Outer shield wire
17 mm
9 mm
Inner covered wire
2. Match wires in the number of terminals and connect them.
•
Do not connect the extended wire to the sensor.
It may cause malfunction by the noise.
•
Do not connect 2 wires or more to the 1 terminal.
ADS-SE1
ADS-SE2
Output
(N.O.)(N.C.)
Power
(12-24 VACᜠ / VDCᜡ)
Emitter
(gray)
Receiver
(blue)
Power
(12-24 VACᜠ / VDCᜡ)
Output
(N.O.)(N.C.)
Emitter
(gray)
Receiver
(blue)
① ②
②
①
■ Connection for sensor / power / output wirings
•
Press the wiring connection buttons and connect
the wires.
•
It does not operate normally if the wires are
connected conversely. Before the wiring, be sure to
check the proper positions of the wires.
•
Make sure that the power wire connects to the
power terminal (4, 5). Otherwise, it may cause
damage to this product.
•
Allowable diameter: in case of the power and output
line
- Single and stranded wire: 0.2 to 1.5 mm
2
■ Cautions during installation
•
Fix a controller with offered 2 fixing bolts.
Process the fixing holes of a controller by M4 and see the ' Dimensions' for the position
of holes.
•
Do not over tighten the bolts when fixing the controller. The fixing holes may be
broken.
Power supply
12 - 24 VACᜠ ± 10 %, 50 / 60 Hz / 12 - 24 VDCᜡ ± 10 % (ripple P-P: ≤ 10 %)
Power consumption
AC: ≤ 2 VA / DC: ≤ 50 mA
Control output
Relay contact output
Relay contact capacity
01)
50 VDCᜡ 0.3 A (resistive load)
Relay contact composition
1c
Relay life cycle
Mechanical: ≥ 5,000,000 times, electrical: ≥ 100,000 times
Insulation resistance
≥ 20 MΩ (500 VDCᜡ megger)
Vibration
1 mm double amplitude at frequency of 10 to 55 Hz (for 1 minute) in each X, Y, Z
direction for 2 hours
Shock
500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times
Ambient illumination
(receiver)
Sunlight: ≤ 100,000 ㏓
Ambient temperature
-20 to 55 ℃, storage: -25 to 60 ℃ (no freezing or condensation)
Ambient humidity
35 to 85 %RH, storage: 35 to 85 %RH (no freezing or condensation)
Protection structure
IP30 (IEC standard)
Connection
Cable connector type
Sensor cable
Ø 2.4 mm, 1-wire, 5 m
Wire spec.
AWG26 (0.16 mm, 7-core), insulator outer diameter: Ø 1.32 mm
Material of the controller
Housing: ABS, cover: ABS, bolt: SCM (brass, Ni-plate)
Material of the sensor
Holder: ABS, lens: PMMA, lens guide: PC, nut: PC
01) Do not use the load which is beyond the rated capacity of contact point of relay.
It may cause bad insulation, contact fusion, bad contact, relay breakdown, and fire etc.
Model
ADS-SE1
ADS-SE2
Available sensor sets
1 channel
2 channels
Sensing distance
0 to 10 m
Sensing target
Opaque materials
Min. sensing target
≥ Ø 20 mm
Sensing method
Through-beam type
Response time
≈ 50 ms (from interrupted light)
Output holding time
≈ 500 ms (from received light)
Light source
Infrared LED (850 nm modulated)
Indicator
OUT 1 indicator (red), OUT 2 indicator (green)
Approval
ᜢ ᜫ
Weight (packaged)
≈ 300 g (≈ 450 g)
Specifications
