manualshive.com logo in svg

Automation Direct igus XYZ Gantry, Руководство пользователя

Поделиться
Скачать
Automation Direct igus XYZ Gantry Скачать руководство пользователя страница 14

Page 14

igus XYZ Gantry User Manual – 1st Ed – 09/14/2022

igus

 XYZ g

antrY

 u

ser

 M

anual

5.  Prepare the Idler Pulley by loosening the 4 Locking Set Screws by a few turns and tightening the Jack Screws all 

the way in.  If the Jack Screws don’t go all the way in, loosen the Locking Set screws further.

6.  Insert the Idler Pulley subassembly into the End Stop with the Jack Screw going in first.

7.  Insert the timing belt through the lower channel of both End Stops and wrap it around both pulleys.

8.  Attach the timing belt to both ends of the Carriage Plate using the belt clamps and screws.

Actuator Part Number

Replacement Belt 

Length (mm)

ZLW1040S-2 / ZLW1080S-2

775

ZLW1040S-3 / ZLW1080S-3

975

ZLW1040S-4 / ZLW1080S-4

1175

ZLW1040S-5 / ZLW1080S-5

1375

ZLW1040S-6 / ZLW1080S-6

1575

ZLW1040S-8 / ZLW1080S-8

1975

ZLW1040S-10 / ZLW1080S-10

2375

Timing Belt Information

Material: Polyurethane with Steel Cords

Tooth Profile: AT5

Belt Width: 16mm

Belt Mass: 0.059 kg/m

Color: White

Содержание igus XYZ Gantry




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды