Automatic Products SNACKSHOP LCM5 Series, Инструкция по эксплуатации

Страница: 11 / 60

7
program operation
6. Vend Option Mode. To enter the vend option mode, press
key [E]. The controller will display “OPtn” and wait for
additional key to be pressed for following features:
a. Press key [A] -
Force Vend.
(displays “FrcY” or “Frcn”)
Press key [A] again to toggle between force vend
enabled (“FcrY”) and force vend disabled (“Frcn”).
b. Press Key [B] - Escrow Enable.
(displays “EScY” or “EScn”)
Press key [B] again to toggle between escrow enable
(“EScY”) or escrow disable (“EScn”).
The escrow enable option allows the validator to return
a bill inserted by a customer who changes their mind.
The bill inserted will be held by the validator without
being stacked. When the coin return button is pushed,
the bill is returned.
c. Press key [C] - Multi-Vend.
(displays “MuLY” or “MuLn”)
Press key [C] again to toggle between multi-vend
enable (“MuLY”) or multi-vend disable (“MuLn”).
The multi-vend option allows the customer the option to
vend multiple items without reentering credit. Change
will not be returned immediately after a vend and cred-
it will remain on the display for up to 20 seconds.
Escrow attempts will be valid at any time or change will
be returned after 20 seconds of no vend activity.
d. Press key [D] - Can Drink.
(displays “CAnY”)
Press [D] again to toggle between “CAnY” and”
CAnn”.
e. Press key [F] - Free Vend.
(displays “FREY” or “FREN”)
Press key [F] again to toggle between Free Vend
Enable (“FREY”) or Free Vend Disable (“FREN”).
The Free Vend option allows the customer to test
vend each selection motor for proper operation.
NOTE:The machine should be on “CAnY”.
components
1 . Power Supply . The 115V AC power cord from the wall
outlet comes into the machine and plugs into the back of
the main junction box located on the bottom right side of
the cabinet. The voltage output to the board is 24 volts
and is plugged in the top right corner (P1 position).
2. Changers. The Snackshop LCM can use a variety of
either Coinco or Mars changers. The machine is wired for
only 24 volt models. The changers available are Coinco
(9302L or 9302LF) and Mars (TRC-6010 or T
R C -
6010XV).In addition, control boards support MDB (Multi-
Drop Bus) peripherals which include coin mechanisms,
validators and card readers. MDB harness is P/N
680576.
3. Controller Board. This module is located on the inside
door (above selector panel) of the vending machine. The
controller will gove
rn all vending activity within the
machine. It has the capability of driving eighty/selections.
4. Mode Switch. The Snackshop LCM has only one mode
switch that allows control of the machine functions. It is
located on the control board. This switch will allow 6
modes of operation.
1. Operate (vending mode)
2. Change payout
3. Accountability
4. Price setting
5. Test vend
6. Vend option
5. Operate Mode. The operate mode is when the machine
is in the normal customer vending mode. The following
steps explain the operation and sequence of events
when making a vend.
a. Digital Display. During standby with no credit in
machine, the digital display will show all zeros with a
designated decimal point. When an alpha-numeric
character is pressed, this selection will be displayed.
b. Credit Operation. Credit may be accumulated through
either a coin changer or bill validator mechanism.
Credit acceptance will disable when the accumulated
credit equals or exceeds the highest priced item. If
using an executive or “Protocol A” type coin mecha-
nism, credit acceptance is controlled by the changer.
The bill validator will be enabled when a combination of
nickels and dimes, or nickels and quarters are avail-
able in the changer.
c. Vend Process. After a keypad entry is made, the con-
troller will determine if sufficient credit is available and
N OT E : Test vending a selection that had failed
p r ev i o u s ly, will reset if the motor successfully
completes a vend cycle.
c. To test vend other selections, press [5] and repeat
steps "a" and "b".
d. To exit this mode, press another function key or leave
Service mode by pressing the mode switch.
PRESS #6 - Diagnostic Vend Test. This feature can be
used to test vend all configured motors within the machine
b e fore installing on location. The controller will display each
selection as a vend attempt is made. If the vend is
successful, the controller will continue on with the next
s e l e c t i o n . If the selected motor fails the controller will
d i s p l ay "FAiL" for 2 seconds and then continu
e. When a
vend attempt on all motors has been completed, the
controller will blank the display and exit the test vend mode.
To exit this mode, press another function key and hold until
the current vend is completed or exit the Service mode.
CAUTION:
THE FOLLOWING PROCEDURE
REQUIRES THAT THE MACHINE HAVE
POWER APPLIED AND A POTENTIAL
ELECTRICAL SHOCK HAZARD EXISTS.
CAUTION:
THE FOLLOWING PROCEDURE
REQUIRES THAT THE MACHINE HAVE
POWER APPLIED AND A POTENTIAL
ELECTRICAL SHOCK HAZARD EXISTS.