TEMPORARY STOP MODE
:
This mode allows the vehicle to remain running after the key has been removed from the ignition. This feature is useful for
occasions when you wish to exit and lock the vehicle for short periods of time but would like to leave the motor running and
the climate control on.
1.
While the vehicle is running, place the transmission in PARK, set the emergency / parking brake.
2.
With your foot off the brake pedal, press the button once, the parking lights will turn on the system has entered
Temporary Stop Mode.
3.
Remove the keys from the ignition and exit the vehicle. Press the button to lock the vehicle’s doors if desired.
Note
: Do not leave children or animals unattended in the vehicle when using the temporary stop feature.
TO TURN OFF THE REMOTE START
When the engine is running (by remote start) and you want to stop it:
1.
Press the button once on the remote transmitter under the remote start mode.
2.
Move the optional remote start enable toggle switch to the “OFF” position. (If installed)
3.
Press the brake pedal.
The vehicle will shut down and turn off the parking light to indicate the engine has stopped
DISABLING THE REMOTE START SYSTEM:
(If Installed)
This feature allows your system’s remote start unit to be temporarily disabled to prevent the vehicle from being remote started
accidentally. This feature is useful if the vehicle is being serviced or stored in an enclosed area. To disable the remote start,
move the optional remote start enable toggle switch to the “OFF” position
TIMER START OPERATION
(See feature
3
-05 setting)
This feature is designed to allow the user to have the system automatically remote start at the end of a selected timed cycle.
Runtime interval based on feature 3-05 option setting.
Activ ate Timer start on / off
Depress
button first then press button to
activate timer start (or if ON, deactivates). A chirp from siren and the parking
light flashes 3 times.
Note:
For Timer Start and Daily Timer Start
:
1.
This will be repeated in 24 hours.
2.
Manually starts or remote starts the vehicle will cancel the timer start.
3.
2 chirps from siren indicate fail setting.
IMPORTANT:
Timer Start and Daily Timer Start should be used only in open areas, never start and run the vehicle in on
enclosed space as a garage or carport.
Contact your installer to reprogram this feature if needed.
SHUTDOWN DIAGNOSTIC :
The unit has the ability to report the cause of the last shutdown of the remote start system.
Press and hold both Buttons
+
simultaneously for 2 seconds until the beep confirms and then release
the button.
4 Button Remote Transmitter:
The parking light and chirps will report the reason of the system last shutdown
by flashing in the following grouped patterns,
GROUP 1
(One Flash of Parking Light)
Chirps
Shutdown Mode
Solution
1
Hood Open
•
Close the hood.
•
Check 16-pin Light Blue wire connection.
2
Optional Enable Switch OFF
or Light Green wire must have
a ground
•
Check 16-pin Light Green wire connection.
•
Move the Enable Toggle Switch to “ ON” position. (If
installed.)
•
Move the gear selector to “ Park”/ “NEUTRAL” position
3
Foot Brake on
•
Check 16pin White wire connection
•
Release Foot Brake.
4
System is in Valet Mode
Exit the Valet mode
5
Hi Voltage
(Voltage Checking Type)
Set the “ Feature 3-02 to “Low Level”
Low or No RPM
(Tachometer Checking Type)
•
Check 16-pin Pink wire connection
•
Set the “ Feature 3-02 to “Hi Level”
•
Re-learning the RPM
6
The engine has run successfully but
is still starting (Tachometer Checking
Type)
Set the “ Feature 3-02 to “Low Level”
GROUP 2
(Tw o Flashes of Parking Light)
Chirps
Shutdown Mode
Solution
1
Alarm triggered
Disarm or Reset Alarm
2
Running Time expired
3
Transmitter Shutdown
4
Over-Rev Shutdown
5
Wait-to-start input
timed out
See the Feature 3-07
(For Diesel Engine Only)
Rem ote Valet
Under disarmed. Press the
button
1
times then press the button. The parking lights will flash once, the remote will read “Valet
On” .
Exit:
Repeat this process to exit valet mode. The parking lights will flash twice, remote read “Valet Off”
TRUNK RELEASE (AUX 1) OUTPUT.
(See feature bank 2-07, 08)
Press and hold the
button on the transmitter for 3
seconds until the beep confirms
and then release the button to remotely control the trunk release
REMOTE START OPERATION
TO REMOTE START THE VEHICLE:
When you want to start your vehicle:
1.
Press the button once on the transmitter.
2.
The parking light will activate to indicate the remote start has received the signal.
3.
After a couple of seconds with the engine running
,
the parking lights will turn on
The countdown timer based on the 3, 10, 20, 30 or 45minutes runtime set up by your installation center. (See feature bank 3-04
setting).
4.
The vehicle will run for a programmable 3 to 45 minutes cycle before shutting down.
When the countdown timer is off or press
button, the system will be shut down,
5.
The vehicle refused to start running after
3
unsuccessful attempts.
6.
If Remote Start fails to start, the parking light will fast flashing 4 times.
PROGRAMMABL E SAFETY START
(See feature bank 3-08)
By default, your Silencer remote starter is programmed to start/stop after pressing the button 1 time. This default setting can be re-
programmed to require 2 presses
-
. This setting is known as “Child Safety Mode”.
Contact your installer to reprogram this feature if needed
.
RUNTIME RESET
If more time is needed while remote start is active, runtime reset will reset the runtime counter to the pre -programmed setting. Follow
the steps below to reset the runtime.
1.
The remote start must already be active.
2.
Press and hold the button for 2 seconds
until the beep confirms and then release the button.
3.
The system will chirp 1 time and flash the parking lights 4 times and the run time Restart
4.
The runtime reset only available when remote start is ON.
ENTERING THE VEHICLE WHILE IT IS RUNNING via REMOTE VEHICLE START
1.
Disarm the system and enter the vehicle, do not step on the foot brake.
2.
Insert the key into the ignition switch and turn to the ON or RUN. The parking lights turn off to indicate remote sta rt is off.
3.
Press the brake pedal. The remote vehicle starter will disengage and the vehicle will operate normally.
