background image

S Y D N E Y

( N S W   &   AC T   S A L E S )

149 Beaconsfield

Street Silverwater

NSW 2128 

Private Bag 149

Silverwater NSW 1811

Phone: (02) 9647 1411

Fax: (02) 9648 3698 

Email:

[email protected]

M E L B O U R N E

( V I C   &   TA S   S A L E S )

22/277 

Middleborough Road

Box Hill VIC 3128 

PO Box 151 Blackburn

South VIC 3130 

Phone: (03) 9890 7477

Fax: (03) 9890 7977 

Email:

[email protected]

B R I S B A N E

( Q L D   S A L E S )

42 Commercial Road

Fortitude Valley 

QLD 4006 

PO Box 871 Fortitude

Valley QLD 4006

Phone: (07) 3852 1312

Fax: (07) 3252 1237 

Email:

[email protected]

A D E L A I D E

( S A   &   N T   S A L E S )

31 Walsh Street

Thebarton 

SA 5031 

PO Box 157 

Hindmarsh SA 5007 

Phone: (08) 8352 4444

Fax: (08) 8352 4488 

Email:

[email protected]

P E RT H

( WA   S A L E S )

299 Fitzgerald Street

West Perth WA 6005 

PO Box 404 

North Perth 

WA 6906

Phone: (08) 9228 4222

Fax: (08) 9228 4233 

Email:

[email protected]

AU C K L A N D

( N Z   S A L E S )

Unit B, 11 Piermark

Drive Albany 1331

New Zealand

PO Box 512 

Albany 1331

Phone: (09) 415 9426

Fax: (09) 415 9864 

Email:

[email protected]

AU S T R A L I A   A N D   N E W   Z E A L A N D

w w w. a u s t ra l i a n m o n i t o r. c o m . a u

I N T E R N AT I O N A L   S A L E S

149 Beaconsfield Street Silverwater NSW 2128 Australia

Private Bag 149 Silverwater NSW 1811

Phone: 61 2 9647 1411 

Fax: 61 2 9648 3698 

Email: [email protected]

S E N N H E I S E R   E L E C T R O N I C   C O R P O R AT I O N

1 Enterprise Drive

Old Lyme CT 06371 USA

Phone: 1 860 434 9190

Fax: 1 860 434 1759 

Email: [email protected]

E U R O P E / A S I A / M I D D L E   E A S T

w w w. a u s t ra l i a n m o n i t o r. c o m . a u

U S A / S O U T H   A M E R I C A

w w w. a u s t ra l i a n m o n i t o r. c o m

Содержание MX61













Отзывы: