AUSTRALIAN MONITOR DigiPage Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 24

AUSTRALIAN MONITOR DigiPage Скачать руководство пользователя страница 11

CAT5 CABLE

CAT5 TERMINATION

CAT5 cable is the blue cable commonly used for data installations (other colours do exist). It
consists of four twisted pairs of wires: this is why it is referred to as UTP (Unshielded Twisted Pair).
The most readily available cable uses solid conductors, like telephone wire. Cable with
stranded conductors is available, and is more flexible.

Pre-wired CAT5 cable comes in two configuration standards, 568A and 568B. It is advisable to
carry a good pre-wired cable for fault-finding. Both configurations will work with the DigiPage
provided both ends have the same configuration. Be careful not to use a crossover cable
which has one configuration at one end and the other configuration at the other end.

Ensure that the RJ45 connectors are suited to the cable used (solid or stranded) and that the
correct crimp tool is used.

When wiring connectors, 568A standard wiring is recommended (see diagram). Note that
this is only the recommended wiring and that you should check the configuration of any
cables that you are using.

INSTALLATION SERIES

Australian Monitor

11

COMBINATION OF DEVICES

MAX DISTANCE

ON SINGLE CAT5 RUN

TO END UNIT (m/ft)

4xWallplates

125m/410ft

2xPaging Stations & 2xWallplates 80m/260ft
3xPaging Stations & 1xWallplate

70m/230ft

1xPaging Station

250m/820ft

2xPaging Staions

125m/410ft

3xPaging Stations

80m/260ft

4xPaging Stations

62.5m/205ft

1xWallplate

500m/1640ft

2xWallplates

250m/820ft

3xWallplates

165m/540ft

1xPaging Station & 1xWallplate

165m/540ft

1xPaging Station & 2xWallplates

125m/410ft

1xPaging Station & 3xWallplates

100m/330ft

2xPaging Stations & 1xWallplates 100m/330ft

White/Green 1

Green 2

White/Orange 3

Blue 4

White/Blue 5

Orange 6

White/Brown 7

Brown 8

568A configuration

CABLE

Shown with

locking clip

facing

Ground
Power
Data+
Busy-
Busy+
Data-
Voice+
Voice-

«
...
9
10
11
12
13
...
»

Содержание DigiPage

























Отзывы:

Нет отзывов