background image

18

GRILL COOKING

ROASTING COOKING

WARMING RACK

Warming racks are a convenient way to keep cooked food

warm or to warm items such as bread or rolls. When opening

the hood, be alert of dripping fat from the warming rack which

could then drip onto the barbecue causing a mess. Always

check that your warming rack is properly fitted before use.

To reduce the risk of serious bodily injury or death:

· If lighting attempts fail, or the burner goes out during 

operation, turn control knob “Off” to dissipate any 

accumulation of gas. Accidental ignition could occur. 

Wait five minutes before repeating lighting procedure.

· When manually lighting side burner, use matchlight 

holder to avoid burns. 

· Do not lean your head or body over the Side Burner 

when manually lighting.

MANUAL LIGHTING THE SIDE BURNER

1. Important: Make sure Side Burner Control Knob is 

turned “Off” first. (See FIG. 15A)

2. Turn the LP Gas Cylinder valve open counterclockwise 

until it stops. (See FIG. 15B) 

3. Push Side Burner control knob in and turn counter 

clockwise to the High position. (See FIG. 15D &17A) 

4. Hold Lit Match near Burner through hole in Side 

Burner Pan from underneath. (FIG. 19)

5. If the burner fails to light, repeat Steps 3 & 4. 

If the burner fails to light after three or four attempts 

following Steps 3-4, turn the side burner control knob 

to the “Off” position and close the LP gas cylinder 

valve to dissipate any accumulated gas. Wait five

minutes; then repeat  the lighting procedures. NOTE: If 

the burners still fail to light, refer to Troubleshooting 

Section. 

FIG.  19

Side Burner Control Knob 

To reduce the risk of serious bodily injury, death or grill

damage:

· Always make sure the Grease Cup is empty and

properly installed in the wire ring under the Bowl before 

cooking to prevent a grease fire . 

· Do not leave any utensils on a hot Cooking Grid or 

cookware. 

Cooking on the Grids: The burners heat up the Flame

Diffusers under the Cooking Grids, which in turn heat the food

on the grill. The natural food juices from cooking fall onto the

hot Flame Diffusers below and vaporize. Rising smoke bastes

the food, giving it that unique barbecued flavor. 

CAUTION

· 

Do not preheat grids over 5 minutes. The porcelain coating 

could be damaged. 

· 

Use only long-handled heat resistant plastic or wooden 

utensils to avoid scratching the porcelain coating.

To avoid burns from the hot air and steam trapped

inside:

· Open the hood carefully when grill roasting. 

OPERATING THE GAS GRILL

To reduce the risk of serious bodily injury or death:

· Never use charcoal in your gas grill. Keep this outdoor 

cooking appliance clear and free from combustible 

materials, gasoline and other flammable vapors and

liquids. 

· Remove grill covers and store at least 36 inches from 

the LP gas grill while in use. Grill covers are made of 

a flammable material. Allow the grill to completely 

cool before putting the cover back on the grill.

· Keep any electrical supply cord and regulator hose 

away from any heated surfaces.

· Do not operate a gas grill if you are aware of or 

suspect a gas leak.

· Make sure there are no gas leaks or obstructions to the 

flow of combustion and ventilation air before each use.

· Keep the ventilation openings of the LP cylinder

enclosure free and clear from debris.

· Always open the hood before lighting the LP gas grill 

to prevent an explosion from accumulation of gas.    

Lit match through

hole in pan

near burner

Closing the Hood forms an ‘oven’ and traps a large amount of

heat for roasting whole meats, chickens, etc. Therefore, it is

IMPORTANT that the burner is turned to the “Low “ position to

prevent burning of the food.
To contain juices and fat, place the food to bake or roast in a

metal baking tray. Monitor the cooking temperature and time

with a meat thermometer. Avoid lifting the hood frequently as

heat is lost each time. 

Содержание AUSSIE 7900

























Отзывы: