background image

 

 

ii

Safety 

IMPORTANT SAFETY INSTRUCTIONS 

1.

 

To disconnect the machine from the electrical Power Supply, turn off the power 
switch and remove the power cord plug from the wall socket. The wall socket 
must be easily accessible and in close proximity to the machine. 

2.

 

Read these instructions carefully. Save these instructions for future reference. 

3.

 

Follow all warnings and instructions marked on the product. 

4.

 

Do not use this product near water. 

5.

 

Do not place this product on an unstable cart, stand, or table. The product may 
fall, causing serious damage to the product. 

6.

 

Slots and openings in the cabinet and the back or bottom are provided for 
ventilation; to ensure reliable operation of the product and to protect it from 
overheating. These openings must not be blocked or covered. The openings 
should never be blocked by placing the product on a bed, sofa, rug, or other 
similar surface. This product should never be placed near or over a radiator or 
heat register, or in a built-in installation unless proper ventilation is provided. 

7.

 

This product should be operated from the type of power indicated on the marking 
label. If you are not sure of the type of power available, consult your dealer or 
local power company. 

8.

 

Do not allow anything to rest on the power cord. Do not locate this product where 
persons will walk on the cord. 

9.

 

Never push objects of any kind into this product through cabinet slots as they 
may touch dangerous voltage points or short out parts that could result in a fire 
or electric shock. Never spill liquid of any kind on the product. 

 
 

CE MARK   

This device complies with the requirements of the EEC directive 2004/108/EC   
with regard to “Electromagnetic compatibility” and 2006/95/EC “Low Voltage   
Directive” 

 

 
FCC 

This device complies with part 15 of the FCC rules. Operation is subject to the   
following two conditions: 

(1) This device may not cause harmful interference.   
(2) This device must accept any interference received, including interference that   
may cause undesired operation 

Содержание NINO II







































Отзывы: