27
Multi-turn actuators SAN 07.1 – SAN 25.1/SARN 07.1 – SARN 25.1
Operation instructions
for valve automation in nuclear power plants
Notes:
Please state type and commission no. of the device (see name plate) when ordering spare parts. Only original
AUMA spare parts should be used. Failure to use original spare parts voids the warranty and exempts AUMA from
any liability. Delivered spare parts may slightly vary from the representation.
No.
Designation
Type
001.0
Housing
Sub-assembly
002.0
Bearing flange
Sub-assembly
003.0
Hollow shaft without worm wheel
Sub-assembly
005.0
Worm shaft
Sub-assembly
005.1
Motor coupling
005.2
Coupling pin
005.3
Manual drive coupling
005.4
Pull rope
006.0
Worm wheel
009.0
Planetary gear for manual drive
Sub-assembly
010.0
Retaining flange
Sub-assembly
017.0
Torque lever
Sub-assembly
018.0
Gear segment
019.0
Crown wheel
Sub-assembly
020.0
Swing lever
Sub-assembly
022.0
Drive pinion II for torque switching
Sub-assembly
023.0
Output drive wheel for limit switching
Sub-assembly
024.0
Intermediate wheel for limit switching
Sub-assembly
025.0
Locking plate
Sub-assembly
058.0
Wire for protective earth
Sub-assembly
061.0
Torque switching head
Sub-assembly
070.0
Motor
Sub-assembly
079.0
Planetary gear for motor drive
(SAN/SARN 07.1 – 14.1 for VDN
motor)
Sub-assembly
080.0
Planetary gear for motor drive
(SAN/SARN 16.1 for ADN90 motor)
Sub-assembly
155.0
Reduction gearing
Sub-assembly
500.0
Cover for switch compartment
Sub-assembly
501.0
Socket carrier (complete with sockets)
Sub-assembly
502.0
Pin carrier without pins
Sub-assembly
503.0
Socket for controls
Sub-assembly
504.0
Socket for motor
Sub-assembly
505.0
Pin for controls
Sub-assembly
506.0
Pin for motor
Sub-assembly
507.0
Plug cover
Sub-assembly
511.0
Screw plug
Sub-assembly
514.0
Output drive form A (without stem nut)
Sub-assembly
514.1
Axial needle roller bearing
Sub-assembly
535.1
Snap ring
539.0
Screw plug
542.0
Handwheel with ball handle
Sub-assembly
549.1
Output drive B3/B4/E
Sub-assembly
551.1
Parallel key
553.0
Mechanical position indicator
Sub-assembly
554.0
Socket carrier with motor cable
harness
Sub-assembly
No.
Designation
Type
556.0
Potentiometer for position transmitter
Sub-assembly
556.1
Potentiometer without slip clutch
Sub-assembly
557.0
Heater
Sub-assembly
558.0
Blinker transmitter including pint at
wires not qualified for nuclear
application (without impulse disc and
insulation plate)
Sub-assembly
559.0
Control unit without torque switching
heads and switches
Sub-assembly
566.0
Position transmitter RWG (not
qualified for nuclear application)
Sub-assembly
566.1
Potentiometer for RWG without slip clutch
Sub-assembly
566.2
Electronic board RWG
Sub-assembly
566.3
Wire harness for RWG
Sub-assembly
567.1
Slip clutch for potentiometer
Sub-assembly
568.1
Stem protection tube (without cap)
568.2
Cap for stem protection tube
568.3
V-seal
569.0
Change-over lever assy
Sub-assembly
569.1
Change-over lever
569.2
Notched pin
574.1
Radial seal output drive A for ISO
flange
575.1
Stem nut (without thread)
579.0
Switch for limit/torque switching
(including pins at wires)
Sub-assembly
580.1
Spacer
581.0
Stud bolt for switches
Sub-assembly
S1
Seal kit, small
Set
S2
Seal kit, large
Set
