AUMA PROFOX PF-M100 Скачать руководство пользователя | Manualshive

Страница: 15 / 48

background image

6.

Electrical connection

6.1.

Basic information

Electric shock due to presence of hazardous voltage!

Failure to observe this warning can result in death, serious injury, or property damage.

→

The electrical connection must be carried out exclusively by suitably qualified
personnel.

→

Prior to connection, observe basic information contained in this chapter.

Wiring diagram/terminal

plan

The pertaining wiring diagram/terminal plan (in German or English) is attached to
the device in a weather-proof bag, together with these operation instructions. It can
also be requested from AUMA (state order number, refer to name plate) or
downloaded directly from the Internet (http://www.auma.com).

Permissible networks

(supply networks)

The actuators are suitable for use in TN and TT networks. For IT network, a suitable,
approved insulation monitor measuring the pulse code is required.

Current type, mains

voltage, mains fre-

quency

Type of current, mains voltage and mains frequency must match the data on the
name plate.

For short-circuit protection and for disconnecting the actuator from the mains, circuit
breakers with the following sizing/characteristics have to be provided by the customer:

Sizing/

characteristics

Number of actuators

B06

1

B10

2

C13

4

D16

10

Potential of customer

connections

All input signals (control inputs) must be supplied with the same potential.

All output signals (status signals) must be supplied with the same potential.

Safety standards

Safety measures and safety equipment must comply with the respectively valid
national on site specifications. All externally connected devices shall comply with
the relevant safety standards for the place of installation.

Connecting cables

Cable glands

Reductions

Blanking plug

●

We recommend using connecting cables and connecting terminals according
to rated current (I

N

) (refer to motor or electrical data sheet).

●

For device insulation, appropriate (voltage-proof) cables must be used. Specify
cables for the highest occurring rated voltage.

●

Use connecting cable with appropriate minimum rated temperature.

●

For connecting cables exposed to UV radiation (outdoor installation), use UV
resistant cables.

●

For the connection of position transmitters, screened cables must be used.

Cable installation in ac-

cordance with EMC

Signal and fieldbus cables are susceptible to interference. Motor cables are
interference sources.

●

Lay cables being susceptible to interference or sources of interference at the
highest possible distance from each other.

●

The interference immunity of signal and fieldbus cables increases if the cables
are laid close to the earth potential.

●

If possible, avoid laying long cables and make sure that they are installed in
areas being subject to low interference.

●

Avoid parallel paths with little cable distance of cables being either susceptible
to interference or interference sources.

15

PROFOX / PF-M25 – PF-M100
Profibus DP

Electrical connection

«
...
13
14
15
16
17
...
»

Содержание PROFOX PF-M100

















































Отзывы:

Нет отзывов

Похожие инструкции для PROFOX PF-M100

Бренд: KEENZ Страницы: 24

Бренд: Ickle Bubba Страницы: 23

Бренд: Gardena Страницы: 18

VLT Micro Drive FC 51 Series

Бренд: Danfoss Страницы: 23

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 24

Бренд: Danfoss Страницы: 60

Бренд: Danfoss Страницы: 10

Бренд: Danfoss Страницы: 20

Бренд: Jedo Страницы: 26

Бренд: Febco Страницы: 12

Бренд: GameSir Страницы: 8

Бренд: Game ready Страницы: 21

Бренд: VAMP Страницы: 304

Бренд: Tactical Страницы: 8

Бренд: IFM Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды