manualshive.com logo in svg

auer dFT3, Руководство по эксплуатации

Поделиться
Скачать
auer dFT3 Скачать руководство пользователя страница 16

16                                                                                                                            dFT3 1.1

Mounting and installing

Protect the telephone from direct rays of the sun and sources of heat.

Wall version

Fasten the telephone mount with 4 screws 

(2)

. Place the provided washers Ø 18 mm under

the screw head.

Place  the  telephone  in  the  upper  latches 

(A)

,  swing  it  downwards  until  the  lower  latches

audibly engage 

(B)

.

Remove the keypad plate 

(6)

, and tighten the two locking screws 

(3) 

as far as they will go.

Important: This preserves the IP65 degree of protection.
Pull the telephone line through the cable gland 

(4)

 and connect it with terminal 

(5) 

TCP/La -

TCP/Lb (TCP : Terminal Connection Point).
Use  cables  with  a  sheath  diameter  of  5  to  9  mm  only,  otherwise  the  IP65  degree  of
protection can not be guaranteed.

Bore
illustration

(not to scale)

Содержание dFT3



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды