background image

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSE

CORRECTIVE ACTION

Receiver won’t power up            

Bad connection

Check your power cord to 
make sure it's plugged 
into the outlet and 
receiver correctly

Transmitter will 
not power up            

Batteries

Make sure they are 
installed correctly (pg 4) or 
check the battery life indicator 
on the transmitter

Lock mode may be ON              

If T-Lock is ON, change to OFF 
(pg 17)

Transmitter
locked up

Software glitch                             

Re-load batteries in order to 
clear memory

No RF signal                                 

Transmitter is not synced 
to receiver

Sync transmitter to 
receiver (pg 7)

Receiver is out of range

Reduce the distance

RF signal is weak                       

Antennas may not be 
connected correctly            

Adjust antennas or use remote 
antennas

Possible frequency 
interference from another 
wireless device

Re-Scan and Sync to another 
frequency (pg 7) or try a lower 
power setting if on a smaller 
stage or venue (pgs 12, 18, 19)

No AF                                          

Transmitter muted                                          

Check transmitter 
ON/OFF button

Transmitter battery 
low or dead                                   

Replace battery

Receiver not hooked 
up properly                                               

Check cable connections on 
both receiver and console, also 
check cable for continuity with 
a cable tester 

AF Signal distorted                   

Transmitter sensitivity setting 
is too high                             

Reduce output level on 
transmitter (pgs 12-13) or
reposition vocal or 
instrument microphone

Receiver level too high                               

Change gain level of receiver
(pg 15)

25

Содержание Performance AP41































Отзывы: