background image

128-7857

9 of 24

9

Purple Wire: 

(+) Door Trigger Input

If the vehicle's door courtesy light sw 12 volts when the door is opened, (Some Fords and some
Imports), you must connect this wire to the positive output from one of the vehicle's door pin switches.  In
most cases, the Purple wire will need to be connected to only one door switch no matter how many doors
the vehicle has as most door lighting circuits are wired in parallel.

Note:

 For vehicles with interior delay lighting see programming under title "Completing The Installation".

Positive Door Switch Wiring Detail

Hood Pin Switch Detail

Dark Green Wire: 

(-) Instant Trigger Input

This is the instant on ground trigger input wire.  This wire must be connected to the hood and trunk pin
switches previously installed.

Note:

 This wire will be shunted when remote control channel 3 is accessed, (trunk release).  This wire will

remain shunted all the while there is ground present and for 5 seconds after the ground is removed.  This
allows the operator to open the trunk via the remote transmitter without having to first disarm the alarm
system.   See below for wiring detail.

Содержание Pursuit PRO-9776

























Отзывы: