MAINTENANCE
Cleaning the unit
Do not use volatile chemicals on this unit. Clean by lightly wiping with a soft cloth.
Cleaning CD
If the CD skips or will not play, the disc may need to be cleaned. Before playing, wipe the disc in a
circular motion from the centre out with a cleaning cloth. After playing, store the disc in its case.
Handing the disc
Only touch the CD on the edge to avoid finger prints on its surface. Do not stick paper or tape nor write
anything on the surface.
SPECIFICATIONS
General
Output (at 1KHz 0db level) Headphones / earphone (stereo minijack)
15 mW + 15mW at 16
Ω
to 32
Ω
Power requirements
2 size “AA” (LR6 or SUM-3) alkaline batteries; or DC in 6V, 350mA power
adaptor
Polarity of plug
Dimensions
Approx. 129 x 30 x 142mm (W/H/D)
Weight
Approx. 225g (not include batteries)
Operating voltage
U.S.A., CANADA
:
120V AC
±
5% 60 Hz
MIDDLE EAST and AUSTRALIA
:
240V AC
±
5% 50 Hz
UK and GERMANY
:
230V AC
±
5% 50 Hz
CHILE
:
230V AC
±
5% 50 Hz
SINGAPORE, MALAYSIA & THAILAND :
200 - 240V AC
±
5% 50 Hz
JAPAN
:
100V AC
±
5% 50/60 Hz
Design and specifications are subjest to change witout notice.
TROUBLE SHOOTING GUIDE
Should and problem persist after you have made the following checks, consult your nearest service
facility.
Disc play does not start :
•
The disc is inserted upside down or incorrectly. Insert the disc correctly with the label surface up
•
Dusty or defective disc
•
Dirty or dusty lens
•
The disc compartment lid is not close
•
Moisture condensation -> Leave the unit in a warm place until the moisture evaporates
•
The AC power adaptor is not plugged into the wall outlet
•
The unit is not placed on a level surface
•
Weak batteries
No sound from the
headsets :
•
The headphones / earphone plug is not firmly connected to the
“PHONES”
jack
•
Adjust the
“VOL”
control
•
Dirty plug
No sound from the connected speakers :
•
Check the connections
•
The amplifier is not turned on
Skipping of sound :
•
Dirty or defective disc
•
Dirty lens
•
Strong vibration
When using with batteries the battery life is short :
•
Manganese batteries are used. Use alkaline batteries.
Display windows shows “
” error message and the unit cannot be
operated :
•
No disc, dirty disc or scratched disc. The unit will return to full stop mode after approx. 30 seconds,
or reset the player by pressing
“
”
once and then insert a disc to start playing.
VARIOUS PLAYING MODES
During playback, every time the
“PLAY MODE”
key is pressed, the mode would be changed to the next
one as follow :
NORMAL PLAY -> “
” (REPEAT ONE) -> “
” (REPEAT ALL) -> INTRO ->
SHUFFLE(RANDOM)
NORMAL PLAY
- Playing the whole disc.
The CD is played once from beginning to end.
REPEAT PLAYBACK (Repeat One and Repeat All)
•
To repeat the same track.
Press
“PLAY MODE”
during play until
“
”
appears
in the display window, Select desired track to be played only once
by pressing
“
”
or
“
”
.
•
To repeat the whole disc.
Press
“PLAY MODE”
during play until
“
”
appears in
the display window.
INTRO PLAY - Playing the first about ten seconds of all the selections:
1. Press
“PLAY MODE”
during play until
“INTRO”
flashes in the
display windows.
2. Press
“
”
to begin the
“INTRO”
play.
3. Pressing
“
”
again will cease the
“INTRO”
play and continue
playback in the
NORMAL
play mode.
*
“INTRO”
play always starts from the first track.
SHUFFLE PLAY - Playing the selections in random order
1. Press
“PLAY MODE”
during play until
“SHUFF”
flashes in the
display window.
2. Press
“
”
to begin in the
“SHUFFLE”
play.
* To locate the next track : press
“
”
. However, you cannot
locate a previous track even if you keep
“
”
pressed.
PROG (Program) play - Playing the selections in the desired order
1. Press
“PRGO”
button until
“PROG”
and
“
”
flash in the display
window.
2. Press
“
”
or
“
”
to select the desired selection.
3. Press
“PROG”
to register track no. 4 for example, as the first
selection. The track no. indication will be returned to
“
”
.
4. Repeat step 2 and 3.
5. Press
“
”
,
“PROG”
stops flashing and program play starts.
NOTES:
*
Repeat play and
“INTRO”
play can be performed during program play.
*
The program is also erased when the disc compartment is opened or the auto power off function turns
the power off.
*
If the program mode is exited by means of the
“
”
key, all the program would still remain in
memory.
Program edition
To check : Press
“PROG”
lightly during programming before you press
“
”
each time
“PROG”
is
pressed the track number appears in the display window.
To change : When checking press either
“
”
or
“
”
to alter track number for the program
currently displayed. Press
“PROG”
to register the newly selected track into memory.
To erase
: When open the CD door including that program will be cancelled.
PRINTED IN CHINA
8 11 - 8 7 0 0 9 1 - 2 5 1
