Audiovox 1286996A, Руководство по установке

Страница: 14 / 28

128-6996A
14 of 28
14
White w/ Blue Trace Wire: 300mA Pulsed or Latched Channel 4 Output
This wire supplies a 300 mA switched output whenever channel four of the receiver is accessed. Pressing the
pre-programmed transmitter button(s) will access channel four and will remain active, for up to 8 seconds, as
long as the transmitter button(s) is held. This is a low current output and must be connected to a relay to supply
power to the device you intend to control. Connect White/ Blue wire to terminal #86 of a VF45F11 P&B relay or
equivalent. Connect terminal #85 of the relay to a fused + 12 volt source. Connect the common, normally open,
and normally closed contacts of the relay to perform the selected function of the channel 4 output.
White w/Green Trace Wire: External Trigger Input
The White w/Green trace wire allows the remote start unit to be activated from an external source. The intent of this
wire is to allow the unit to be controlled from a "POSSE/CAR-LINK" paging system or similar device. When this
wire receives a ground pulse, the unit will start the vehicle. Connect this wire to a ground pulsed output from the
controlling circuit.
Brown w/ Black Trace Wire: 300 mA Horn Output
The Brown w/ Black trace wire is provided to beep the vehicle’s horn. This is a transistorized low current output,
and should only be connected to the low current ground output from the vehicle’s horn switch.
If the vehicle uses a + 12 VDC horn switch, then connect this wire to terminal 86 of the AS 9256 relay ( or an
equivalent 30 Amp automotive relay ), and connect relay terminal 85 to a fused + 12 VDC battery source. Connect
relay terminal 87 to the vehicle’s horn switch output, and connect relay terminal 30 to a fused + 12 VDC battery
source.
Green w/ Orange Trace Wire: Low Current (-) Ground Headlight Output
The Green w/ Orange Trace wire is provided to operate the optional headlamp illumination feature of the system.
This is a low current (300mA) output and must be connected to an external relay to control the high current
switching circuit of the vehicle's headlamps. To use this option, Connect this wire to terminal # 86 of a P&B
VF45F11 relay or equivalent. Connect Terminals #85 and # 30 to a fused + 12 Volts source with a current capability
equal to or in excess of the factory headlamp fuse. Connect terminal # 87 of the relay to the sw 12 volt wire
feeding the vehicle's headlamp circuit.
NOTE: For ground switched headlamp circuits, Connect this wire to terminal # 86 of a P&B VF45F11 relay or
equivalent. Connect Terminal #85 to a fused + 12 Volts source. Connect terminal # 30 to a clean chassis
ground. Connect terminal # 87 to the ground switched headlamp control wire in the vehicle.
Empty Cavity: Empty Cavity In Connetor No Function
Blue w/White Trace Wire: (-) Instant Trigger Zone 1
This is a instant on ground trigger input intended for the connection of optional triggering devices. The ground
trigger output wire of motion detectors, microwave detectors, or glass break detectors, can be connected to this
trigger input wire.
Purple w/Black Trace Wire: 300 mA Pulsed or Latched Channel 5 Output
This wire pulses to ground via an independent RF channel from the keychain transmitter. This is a transistorized,
low current output, and should only be used to drive an external relay coil.
WARNING: Connecting the Purple/Black wire to the high current switched output of trunk release circuits, some
remote start trigger inputs, will damage the control module.
Connect the Purple/Black wire to terminal 86 of the AS - 9256 relay (or equivalent 30 A automotive relay), and wire
the remaining relay contacts to perform the selected function of channel 5.
White w/Black Trace Wire: 300 mA Pulsed Cannel 6 Output
This wire pulses to ground via an independent RF channel from the keychain transmitter. This is a transistorized,
low current output, and should only be used to drive an external relay coil.
WARNING: Connecting the white/black to the high current circuits, will damage the control module.
Connect the white/black to terminal 86 of the AS - 9256 relay (or equivalent 30 A automotive relay), and wire the
remaining relay contacts to perform the selected function of channel 6.
Lt. Blue w/ Black Trace Wire : 300 mA Pulsed Channel 7 Output
This wire pulses to ground via an independent RF channel from the keychain transmitter. This is a transistorized,
low current output, and should only be used to drive an external relay coil.