Audiopax 88 Скачать руководство пользователя страница 5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

Installation 

 

Your 

Model 88 

is shipped in two boxes containing: 

 

  Two monoblocks (one for each channel) 

  Two tube quartets (each with two input and two power tubes) 

  Extra fuses 

 

Your manual is available for download from our website: 

www.audiopax.com.

 

 
The monoblocks should be installed in an airy area, avoiding enclosed spaces (such as 

cabinets) and maintaining an empty surface of at least 30 cm above them. As your on/off switch 
is located at the rear of the equipment, it is also important that this space is easily accessible. It 
achieves optimal operating conditions within 30 minutes and should be turned off whenever long 
periods until the next listening session may occur (this recommendation is made to extend the 
life of your tubes). For the best sound, we advise you to also install it in a location free of excess 
bass, avoiding interference and feedback in your tubes (as room corners). 

 
With the monoblock already in its final position, it is now necessary to install the tubes, 

which will only fit in its correct position. For the 12AT7 (input tubes), you just have to match the 
biggest distance between their pins with the same space at the sockets. For the KT88s (power 
tubes), you just have to match the guide plastic pin below it with the hole at the sockets. Once 
the correct position is reached, gently press each tube until its base fully touches the socket and 
they are 100% perpendicular to the chassis. 

 
Without connecting the AC cable, make sure that the “

Power On/Off

” switch on the rear 

of  each  one  of  the  amplifiers  is  in  their  “

Off

”  position.  Connect  the  signal  input  RCA  cables 

(black/white:  left  channel;  red:  right  channel),  the  speaker  cables  to  the  appropriate  binding 
posts  (taking  care  to  put  both  with  the  same  polarities).  Finally  connect  the  power  cord  to  the 
IEC connector, respecting the nominal voltage of your 

Model 88

 (120V or 230V). 

 

 

Содержание 88













Отзывы: