Volume
Press to raise or lower the volume. The
VOLUME control on the front panel turns.
Gain Switch
Unpacking
This enables you to operate the volume control over a wide area
Unpack the product fully. The carton should contain
while minimising noise. For initial installations, set gain to 9dB.
(
The Audiolab 8000Q
REDUCE Gain: high sensitivity loudspeakers, low level listening.
(
One IEC power cord suitable for your area
INCREASE Gain: low sensitivity loudspeakers, low output sources.
(
One Remote Handset with two AA batteries
(
When changing gain the 8000Q will briefly mute.
(
This instruction manual
(
Altering the gain will not affect the Record Outputs.
Report any damage or shortage to your dealer as soon as possible.
Volume Control
Retain the packing if possible. If you dispose of the packing, do so
Adjusts playing volume. Always turn the volume up gradually.
with regard to any recycling regulations in your area.
Turn the volume down before changing inputs.
Inserting Batteries in the Handset
Record Selector
The battery compartment is on the rear of the handset. Unwrap the
Turn to select source to record to Tape 1, Tape 2 or Video. You can
batteries, open the compartment cover and insert the batteries.
record to any CD, tape or other recorder with analogue inputs.
Follow polarity indications in the battery compartment. Replace
Record selector and input selector operate independently. It is
batteries in pairs. Use new batteries of the same type and rating.
possible to record from any source whilst listening to another.
Controls and Functions
Mute
(available on the Remote Handset)
Power Switch
Toggles the pre-amp output On/Off. Recording is unaffected.
When power is switched on the 8000Q is muted for 3 seconds.
Headphone Socket
Input Selector
Socket for connection of headphones. Unplug headphones when
Turn to select the listening source. The 8000Q mutes briefly when a
not in use. Connecting headphones mutes the 8000Q.
new input is selected.
2a: Introduction- 8000Q
RECORD
SELECTOR
INPUT
SELECTOR
HEADPHONE
SOCKET
POWER
SWITCH
POWER LED
RED=Power On
MUTE LED
RED=Mute On
Input
Press to select listening source. The INPUT
selector on the front panel turns.
If you wish to record, the record input must be
selected manually.
Mute
Toggles mute On/off.
Remote Handset
Buttons shown in white control the 8000Q.
Buttons shown in grey operate Audiolab CD
players and have no effect on the 8000Q.
As the handset uses RC5 coding it will operate
many CD players. Check with your dealer.
Phase
Switching On
It is essential that the loudspeaker connections are secure and with
Make sure all the signal and loudspeaker connections to and from
the positive and negative terminals correctly connected.
the amp are secure and correctly made.
This becomes especially important in bi-wired and bi-amplified
Plug the power cords into the pre-amplifier and the power
systems where the effects of one or more incorrectly connected (out
amplifier/s and then into the wall socket .
of phase) loudspeakers may severely impair the sound and yet be
Switch on at the mains and then switch on the pre-amlifier
difficult to detect.
followed by the power amplifier/s.
The power indicators on all the units will light showing the system
If the sound appears muddled and lacking clarity this may be
is operational.
because one or more speaker connections are not correctly made.
Always check loudspeaker connections carefully when you have
The 8000Q pre-amplifier may be operated via the front panel or
made any alteration to your system.
the remote handset.
Maintaining Connections
When you have finished using the equipment switch off all the
power amplifiers. Some enthusiasts prefer to leave the pre-
Connections should be checked periodically. If necessary the plugs
amplifier permanently switched on. If you do this, ensure that the
should cleaned with a proprietary cleaner or, in the case of
pre-amplifier is set to mute with the volume control at minimum.
loudspeaker connections, freshly re-made.
800Q
VOLUME
CONTROL
REMOTE
CONTROL SENSOR
GAIN
SWITCH
A note should be enclosed giving your
Care & Cleaning
name, address, telephone number, and a
While cleaning is in progress the AC power
brief description of the reason for return.
cord must be unplugged from the AC
If you require Service outside the Warranty
power supply socket.
period, do not hesitate to contact your
Grease or dirt on the equipment may be
dealer.
removed with a soft, lint-free cloth slightly
moistened with a mild solution of warm
Service Address - UK
water and detergent or washing-up liquid.
Do not use any other solutions or solvents.
IAG Service Centre
Unit 4
If you have any queries regarding the use
St Margaret’s Way
of Audiolab equipment, consult your
Stukeley Meadows Industrial Estate
dealer.
Huntingdon
Servicing
Cambs
Servicing of Audiolab products should only
PE29 6EB
be carried out by authorised service
England
agents. If service is required the
452561
equipment should be returned, securely
13403
packaged, preferably using original
Service Address - USA
packaging, to your dealer.
In the UK equipment may be returned to
the IAG Service Centre. In the USA
equipment may be returned to the Service
address shown on this page.
Always telephone before returning any
equipment.
Tel:+44 (0)1480
Fax: +44 (0)1480
IAG America, Inc.
15 Walpole Park South
Walpole
MA 02081
USA
Tel: +1 508 850 3950
Fax +1 508 850 3905
6: Service
5: Operation
Bi-Amplified connection- 8000Q with four 8000M power amplifiers
LEFT
RIGHT
