background image

-----------------------------------------------26 ----------------------------------------------

Troubleshooting

It is important to remember when installing your LC6i that the engi-

neers who work for the car manufacturers don’t spend too much time 

thinking about interfacing after market products.  Therefore you will 

most likely have to “modify” your traditional wiring and installation 

techniques when working with these types of systems.  Many times tra-

ditional 12 Volt “turn-on” wires or pre-amp audio signals that you are 

used to with aftermarket systems don’t exist on these newer vehicles.

No Power:

 If the Power LED on your LC6i will not turn on, check to 

make sure that the power wire and remote turn-on wires are connect-

ed or a fuse has not blown, and that your factory head unit is on! 

LC6i Turns Off Intermittently:

 If you are using the GTO signal sensing 

to turn on your LC6i yet your system is turning off, this may be due to 

a cellular phone interface or navigation system built in to your factory 

installed source unit.  These are known to route the audio signal away 

from your source unit’s outputs.  In these situations it is recommended 

that you connect a 12-Volt trigger wire from the Remote In on the LC6i.

Sounds Distorted:

 Should your system sound distorted or your speak-

ers are moving way too much, you should make sure you have your lev-

els matched properly and that your amplifier gains are set at minimum.   

System Hiss:

 Check to make sure that your amplifier gains are set at the 

minimum level.

Turn-On Pop or Turn-Off Pop:

  This generally occurs when your ampli-

fiers are turning on or off at a different time than your LC6i.  Therefore 

it is recommended that you use the “Remote Out” on your LC6i to turn 

your amplifiers on or off and eliminate any timing issues.

Содержание LC6i

































Отзывы: