background image

Page  3 of 19

AudioCodes™ MP-104 Gateway Quick Start Installation Guide

August 2004

Quick Start Installation Outline

The following steps outline the MP-104 installation. For details, refer to the pages
shown in parentheses in each step.

To install the MP-104:

1.

Unpack the box and check the parts list to make sure nothing is missing from the
shipment.

2.

Set up the MP-104 gateway device through the AudioCodes BootP/TFTP Server
program (see 

page 4

). 

NOTE: 

Ensure you have added the -fb command to the 

ramMP1XXFXO.cmp

and this file is selected as the Boot file (see 

page 7

)

3.

Reset the Server. Progress can be viewed in the BootP/TFTP Server window
(make sure it is not paused). See 

page 9

4.

Configure the MP-104 application through the AudioCodes MP-104 Web
administrator (see 

page 19

). 

5.

Verify that the 

Call Agent IP

 

address in the Advanced Configuration - Protocol

Management page matches the IPRC IP address (see 

page 12)

.

6.

Configure the IPRC ports through the IPRC Administrative Session Web page
and verify the following:

 •

The gateway is configured as an MGCP gateway and endpoint (the first cir-
cuit), and each additional endpoint is attached to the correct circuit (see

page 19

).

 •

All information is correct (MAC address, IP address, etc.).

 •

The connection is active in the Circuit Status page.

The AudioCodes MP-104 Gateway is now ready for connection to the CO.

Содержание MP-104




















Отзывы: