manualshive.com logo in svg

AudioCodes MP-100, Быстрый старт

Поделиться
Скачать
AudioCodes MP-100 Скачать руководство пользователя страница 1

Page  1 of 17

AudioCodes™ MP-100/104 Gateway Quick Start Installation Guide

March 2004

AudioCodes™ MP-100/104 Gateway

Quick Start Installation Guide

INTRODUCTION

This quick start guide contains information about how to install and configure the Audio-
Codes™ MP-100/104 Gateway. Although this guide covers both the MP-100 and MP-104
Gateways, the installation instructions apply to the MP-104. This gateway is the latest version
that is available through the Inter-Tel

®

 CommSource™ division. For details about the MP-100,

refer to the latest version of the

 IP Devices Manual

.

SYSTEM REQUIREMENTS

The following lists the system requirements for installing the AudioCodes MP-100/104 Gate-
way:

•

Internet Protocol Resource Card (IPRC) firmware v1.3 or later

NOTE: 

To support Session Initiation Protocol (SIP) on the AudioCodes MP-100/104

Gateway, v1.5 or later firmware is required.

•

Axxess

®

 v7.0 or later

SYSTEM DATABASE PROGRAMMING 

The IPRC firmware version determines how Axxess is programmed to support the gateways.
For details about system database programming, refer to the documents listed below. 

If you are installing the gateway on a:

•

V1.x firmware

 

IPRC

, see the latest version of the 

IP Devices Manual

. 

•

V8.x firmware IPRC

, see the

 Addendum to the v8.0 Installation and Maintenance Man-

ual

.

AUDIOCODES MP-100 GATEWAY INSTALLATION

For details about installing the AudioCodes MP-100, refer to the latest version of the 

IP

Devices Manual.

Document Part Number 835.2741-3

A946/3852A

© Inter-Tel, Inc. March 2004 printed in USA

Содержание MP-100


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды