AudioBahn A16000J Скачать руководство пользователя

Страница: 25 / 32

Below you will find information on adjusting the amplifiers gains. Adjusting the gain correctly is essential to

proper operation of the amplifier.

If the gain is not adjusted properly it can and will lead to damage of

the amplifier and connected speakers and will void your MANUFACTURER WARRANTY

The gain on

an amplifier is not a volume control. It is a signal level setting that tells the amplifier how strong of a signal

is coming from the head unit. Your amplifier has an input sensitivity of 200mV-8V. The minimum setting is

8V and the maximum setting is 200mV. Minimum meaning the head unit or processor has 8V output and the

maximum meaning it has a 200mV output.

When using

Low-Level (RCA) inputs

you MUST know what the pre-out or line-out voltage of your head

unit is rated in Volts. This is not the wattage rating. This can be found in the manual of the head unit or by

contacting the manufacturer. If you are using a line-driver or another type of processor that adjusts the output

voltage of the signal to the amplifier you will need to know what the output is adjusted to. The gain on the

amplifier needs to be set proportionately to the pre-out or line-out voltage rating of the head unit or processor.

If the signal strength is 4V then the gain would be adjusted to about 45 - 50%. Below is a list of commonly

found voltage ratings and their appropriate gain adjustments. When adjusting the gain you want to start with

the bass boost setting on the amp set to minimum and bass adjustments on the head unit or processor are

set at 0 or flat. As these other settings for bass adjustments are increased, the gain setting will need to be

adjusted lower.

2V ≥ 70%

4V ≥ 45%

5V ≥ 32.%

8V ≥ 5% (Bass boost must be left at minimum on the amp and 0 or flat on the head unit or processor)

10V ≥ Can not be used with this amplifier.

If your amplifier includes

Hi-Level (speaker wire) inputs

and you are using them for the audio signal connec-

tion, please use the below steps to adjust the amplifier. Start with a song with good bass that you know very

well.

Use a screwdriver to turn GAIN (8V / 0.2V fully counter clockwise to 8V

Turn the auto sound system’s volume control to about 3/4 of its full range. Any higher normally

leads to the signal being distorted.

Turn up the amplifiers gain / level control unit the sound begins to distort, then immediately gain /

level down to a point just before where the distortion began.

Adjust the auto sound system’s volume control to a comfortable listening level and you are good to

go.

NOTE: The steps to adjusting the gain / level control need to be repeated when you adjust any bass boost

setting on the amplifier, processors or significantly on the head unit. Adjusting bass boost settings signifi-

cantly without adjusting the gain / level can lead to a distorted signal and damage to the amp and speakers.

IMPORTANT NOTE: If you should have any questions concerning the installation or set-

tings on your amplifier or are unsure of anything discussed in this manual, please contact

our Technical Support department at 714.452.1476 for help. It is much better to take 5

minutes today to get it right then to adjust the settings incorrectly and have a problem

with your amp or speakers.

ADJUSTMENTS AND TUNING

Содержание A16000J

































Результаты поиска

Содержание A16000J

Отзывы:

Похожие инструкции для A16000J

Бренды по названию

Популярные бренды

AudioBahn A16000J, Руководство пользователя

Результаты поиска

Содержание A16000J

Отзывы:

Похожие инструкции для A16000J

Бренды по названию

Популярные бренды