Form No. 0309-2108-02 P51796 © 2005 Audio-Technica U.S., Inc. Printed in U.S.A.
Element
Fixed-charge back
plate permanently
polarized condenser
Polar Pattern
Hypercardioid
Frequency Response
80-20,000 Hz
Low-frequency Roll-off
80 Hz, 18 dB/octave
Open Circuit Sensitivity
–39 dB (11.2 mV)
re 1V at 1 Pa
*
Impedance
200 ohms
(1000 ohms without
power module)
Maximum Input Sound
127 dB SPL, 1 kHz at
Level
1% T.H.D.
Dynamic Range
98 dB, 1 kHz at
(typical)
Max SPL
Signal-to-noise Ratio
1
65 dB, 1 kHz at 1 Pa
*
Phantom Power
11-52V DC, 4 mA
Requirements
typical
Switches
Flat, roll-off; 0 dB,
+10 dB gain setting
Weight
Microphone
0.2 oz (5 grams)
Power Module
3.4 oz (97 grams)
Dimensions
Microphone
0.92" (23.3 mm)
long, 0.33" (8.4 mm)
head diameter
Power Module
2.80" (71.0 mm) W x
4.55" (115.5 mm) H x
1.42" (36.0 mm) D
Power Module
Screw terminals
Connectors
Cable
50' (15.2 m) long
(permanently
attached to
microphone), 0.13"
(3.2 mm) diameter,
low-noise shielded
cable with pigtail
output
Accessories Furnished
(ES933PM/H)
AT8109 two-stage
foam windscreen;
AT8452 steel hanger
(ES933PMW/H)
AT8109(WH)
two-stage foam
windscreen;
AT8452(WH)
steel hanger
(Both)
AT8534 power
module
Optional Interchangeable
ESE-C cardioid
Elements
(120°)
ESE-ML MicroLine
®
(90°)
†
In the interest of standards development, A.T.U.S. offers full details
on its test methods to other industry professionals on request.
*
1 Pascal = 10 dynes/cm
2
= 10 microbars = 94 dB SPL
1
Typical, A-weighted, using Audio Precision System One.
Specifications are subject to change without notice.
One -Year Limited Warranty
Audio-Technica microphones and accessories purchased in the U.S.A. are warranted for one year from date of pur-
chase by Audio-Technica U.S., Inc. (A.T.U.S.) to be free of defects in materials and workmanship. In event of such
defect, product will be repaired promptly without charge or, at our option, replaced with a new product of equal or
superior value if delivered to A.T.U.S. or an Authorized Service Center, prepaid, together with the sales slip or other
proof of purchase date.
Prior approval from A.T.U.S. is required for return.
This warranty excludes defects due
to normal wear, abuse, shipping damage, or failure to use product in accordance with instructions. This warranty
is void in the event of unauthorized repair or modification.
For return approval and shipping information,
contact the Service Department, Audio-Technica U.S., Inc., 1221
Commerce Drive, Stow, Ohio 44224.
Except to the extent precluded by applicable state law,
A.T.U.S. will have no liability for any consequential,
incidental, or special damages; any warranty of merchantability or fitness for particular purpose expires
when this warranty expires.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
Outside the U.S.A., please contact your local dealer for warranty details.
The microphone shall be a fixed-charge
condenser with a frequency response of
80 Hz to 20,000 Hz and a hypercardioid polar
pattern with uniform 100° angle of acceptance.
It shall be capable of accepting optional inter-
changeable elements for additional polar
patterns. It shall operate from an external 11V
to 52V DC phantom power source. It shall be
capable of handling sound input levels up to
127 dB with a dynamic range of 98 dB. Nominal
open-circuit output voltage shall be 11.2 mV at
1 kHz, 1 Pascal. Output shall be low impedance
balanced (200 ohms).
The microphone shall have a permanently-
attached 50' (15.2 m) miniature low-noise
cable with a pigtail output. The pigtail output
shall connect to screw terminals on the power
module, which shall incorporate a face plate
mountable to a single-gang electrical box for
wall or ceiling installation. Output connections
on the power module shall be screw terminals.
The power module shall include switches for
low-frequency roll-off and 10 dB gain setting.
The microphone shall be mountable in an
included adjustable steel wire hanger that
allows permanent overhead installation for
pickup of dialogue, orchestras and choirs. A
snap-on foam windscreen shall be provided.
The microphone shall be 0.92" (23.3 mm) long
with a head diameter of 0.33" (8.4 mm). The
microphone weight shall be 0.2 oz (5 grams)
without cable.The microphone case, cable and
steel hanger shall be finished in black [white].
The Audio-Technica ES933PM/H
[ES933PMW/H] is specified.
[
ES933PM/H Specifications
†
]
YEL/YEL
RED/RED
SHIELD
23.3 mm
0.92"
0.13"
3.2 mm
15.2 m
50'
8.4 mm
0.33"
[
Dimensions
]
[
Polar Pattern
]
90
200 Hz
LEGEND
8 kHz
5 kHz
1 kHz
270
240
210
SCALE IS 5 DECIBELS PER DIVISION
180
150
120
300
330
30
0
60
Architects and
Engineers
Specifications
[
[
[
Visit our Web site at www.audio-technica.com
]
Audio-Technica U.S., Inc.
1221 Commerce Drive, Stow, Ohio 44224
[
Frequency Response
]
20k
200
Roll-off
12" or more on axis (flat)
LEGEND
50
100
2k
Frequency in Hertz
500
1k
5k
10k
Response in dB
10 dB
[
Power Module
]