Audio Technica Artist Elite 4000 Series, Инструкция по установке и эксплуатации

Страница: 10 / 41

11
Figure D AEW-R5200 Receiver Rear Panel
IN
ANT. B
OUTPUT
(BAL)
INSTRUMENT
EXTERNAL
MUTE
0/-6/-12
ATTN (dB)
BALANCED
MIC OUTPUT
GROUND
LIFT
GROUND
NETWORK
INTERFACE
IN
ANT. A
OUTPUT
(BAL)
INSTRUMENT
EXTERNAL
MUTE
0/-6/-12
ATTN (dB)
BALANCED
MIC OUTPUT
GROUND
LIFT
GROUND
AC
˜
100V-240V
50/60Hz
OUTPUT
5A/500W MAX
WARNING:
THIS APPARATUS
MUST BE EARTHED.
IN
LINK
OUT
29 30
Rear Panel Controls and Functions (Fig. D)
14 ANTENNA INPUT JACK: BNC-type antenna connector for
Tuner “B.” Attach the antenna directly, or extend it with a
low-loss antenna cable. See the ”Antennas” section on
page 8 for more details. Antenna power at +12 volts is
available at both antenna jacks; select it via the LCD menu
on Channel 1.
15 / 22 EXTERNAL MUTE: Permits manual and absolute
muting of the receiver via a 1 /
4
" TS phone jack and a user-
provided external switch. “Shorting” the jack (closing the
switch connection) mutes the receiver channel. When
External Mute has been applied, the only way to un-mute
the receiver is to open the External Mute switch connection.
16 / 23 INSTRUMENT OUTPUT JACK: 1 /
4
" transformer-isolated
TRS balanced phone jack output. Tip: “audio +”; Ring:
“audio –”; Sleeve: ground (shield). Can be connected to an
aux-level input of a mixer, guitar amp or tape recorder. Using
the associated Ground Lift switch permits feeding
equipment with different ground levels.
17 / 24 AF OUTPUT ATTENUATOR: Three-position switch
adjusts audio output level of both audio output jacks, with
attenuation of 0 dB, –6 dB or –12 dB.
18 / 25 MIC OUTPUT JACK: XLRM-type connector. Pin 1:
ground (shield); Pin 2: “audio +”; Pin 3: “audio –”. A
standard 2-conductor shielded cable can be used to connect
the receiver output to a balanced microphone-level input on
a mixer or integrated amplifier. This output is transformer-
isolated from the
1 /
4
" TRS Instrument output jack.
19 / 26 GROUND LIFT SWITCH: Disconnects the ground of
both the Mic and Instrument output jacks on the associated
receiver channel. Normally, the switch should be to the right
(ground connected). If hum caused by a ground loop occurs,
slide switch to the left (ground lifted).
20 NETWORK INTERFACE CONNECTOR: An Ethernet
connection on the AEW-R5200 provides full communication
and monitor/control by an associated computer. See the
separate AEW Control Interface manual for computer setup
and operation.
21 ANTENNA INPUT JACK: Connector for Tuner “A.” Attach
the antenna directly, or extend it with a low-loss antenna
cable.
27 LINK IN JACK: Connect the provided cable to this jack with
the index mark on the plug aligned toward the screw head to
the right of the jack. The receiver with a Link In and no Link
Out connection is the “Master” unit. (With an AEW-R5200 in
the Master position, its Channel 1 is the system’s Master
and its Channel 2 is the first “slave.”)
28 LINK OUT JACK: Connect the provided cable to this jack
with the index mark on the plug aligned toward the screw
head to the right of the jack. The receiver with a Link Out
and no Link In connection is the last slave in a multi-unit
system.
29 AUXILIARY AC OUTLET: An auxiliary AC pass-through outlet
and included “jumper” power cordset simplify making power
connections to an array of AEW-R5200’s. Maximum output
from the auxiliary AC outlet is 5 Amperes.
30 AC POWER INPUT: IEC-type connector for 100V–240V AC,
50/60 Hz power input. No adjustment for mains voltage/
frequency is necessary.
31 REAR RACK MOUNT: Mounts are provided at the rear of the
side panels to permit attachment to rear rack rails in racks so
equipped. The additional support is especially helpful when
equipment is transported.
Receiver Controls and Functions
(Continued)
31 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 31
4000 & 5000 OM (Nov.08).qxd:4000 & 5000 OM 2/04.2 26/11/08 16:22 Page 11