Audio Precision AP 517 Скачать руководство пользователя страница 21

Страница: 21 / 92

Installation

APx517 B Series Acoustic Analyzer: Installation

cessfully installed, connect one end of the USB cable to a

USB 2.0 port on the PC, and the other end to the PC

INTERFACE port on the rear of the APx517. We strongly

recommend that you use the USB cable included with your

instrument (AP part number CAB-APSI). We have tested

other USB cables that perform poorly.

Note: Some PCs have optional USB ports on the

front of the PC, or on extension brackets on the

rear. In many cases these convenience ports

have compromised performance due to the extra

cable length within the PC. We recommend using

USB ports directly connected to the PC mother-

board, typically at the rear of the PC.

Connect the APx517 mains power cord to the instrument

and to a source of ac mains power. See the

Mains Power

and Fusing

section that follows for more information about

mains connections.
Turn the instrument on by rocking the mains power switch

(

). The mains power switch is located in the power

entry module on the rear of the APx517. Windows will

detect the presence of the APx517 on the USB port and will

open the Hardware Update Wizard to search for the correct

software driver. Select “Install the software automatically.”

Windows will find the Audio Precision driver software

installed with APx500 and connect to the APx517.
Launch APx500 by double-clicking on the installed short-

cut. With the APx517 connected, you may be asked to

update the instrument firmware during the first launch of

the measurement software. APx500 will start, and in a short

time you will be presented with the opening screen. Refer to

the APx500 User’s Manual for more information about

making measurements.

The APx500 User’s Manual is available as a PDF

on the APx500 Application Disc and online at

ap.com; a hard-copy version can be ordered from

Audio Precision or your local distributor.

Mains Power and Fusing

Connect the APx517 mains power cord to the instrument
and to a source of ac mains power. Turn the APx517 on by

rocking the mains power switch to

(

). The mains

power switch is located in the power entry module on the

rear of the analyzer.

Connecting your instrument to the electrical

mains supply

A n APx517 must be connected to a 50–60 Hz alternating

current (ac) electrical mains supply. The minimum voltage
is 100 Vac; maximum voltage is 240 Vac. Use only ade-

quately rated detachable mains power cords.
The analyzer is fitted with a universal power supply that

does not require voltage configuration or change of fuse
type to accept mains voltages within the specified range.

Removing and installing mains fuses

For all rated voltages, use two mains fuses of type

• 4 A T/SB (5

20 mm) 250 V.

Use only certified fuses of the appropriate specifications.
To remove the mains fuse carrier module, refer to the fig-

ures below and proceed as follows:

Содержание AP 517





























































































Результаты поиска

Содержание AP 517

Отзывы:

Бренды по названию

Популярные бренды

Audio Precision AP 517, Руководство по установке

Результаты поиска

Содержание AP 517

Отзывы:

Бренды по названию

Популярные бренды