Audio Note AN-J Скачать руководство пользователя страница 10

CONNECTION TO AMPLIFIER 

 
 
 
 
 
 

 
On  the  rear  of  your  amplifier,  identify  the  loudspeaker  output  terminals;  they  should 
be labeled 

ʻ

LEFT

ʼ

 and “RIGHT

ʼ

Facing  your  amplifier  and  loudspeakers,  connect  the  left  loudspeaker  to  the 

ʻ

LEFT

ʼ

 

loudspeaker  outputs  on  your  amplifier,  and  the  right  loudspeaker  to  the 

ʻ

RIGHT

ʼ

 

loudspeaker outputs on your amplifier. 
 
If  your  amplifier  is  equipped  with  multiple  loudspeaker  output  terminals,  consult  the 
manual for the unit to ascertain the appropriate connection regime. 
 
The facility to split the crossover of the AN-J

 

allows the speakers to be operated in a 

bi-wired  or  bi-amplified  mode.  The  crossovers  are  split  by  removing  the  connecting 
links between the HF and LF terminals on the rear of the speaker. 
 

Bi-wiring

  

 

This  involves  running  two  sets  of  cables  to  the  rear  of  each 

 

 

 

speaker, so that the Low Frequency (LF) section of the  

 

 

 

crossover is fed by one set and the High Frequency (HF)  

 

 

 

section by the other. Both sets of cables are attached together 

 

 

 

to the corresponding pair of terminals on the back of the  

 

 

 

amplifier. 

 

 

 

We strongly recommend bi-wiring the AN-J with a suitable 

 

 

 

loudspeaker cable from the Audio Note (UK) range. 

 

Bi-amplifying

  

This  involves  using  two  stereo  or  four  mono  power  amplifiers 

 

 

 

to drive the loudspeakers. If you intend to 

ʻ

bi-amp

ʼ

 the  

 

 

 

AN-J, please consult your amplifiers manual(s) for the  

 

 

 

appropriate connection regime. 

 

If you are in any way uncertain as to the correct method of connection for your 
amplifier or loudspeakers, please consult your Audio Note (UK) dealer. 
 

 

Special  Note  –  Make  sure  that  all  connections  are  tight  and  clean.  For  best  results 

use  good  quality  loudspeaker  cables.  Although  it  is  perfectly  acceptable  to  use 
cables  manufactured  by  other  companies,  for  best  results  and  performance,  we 
recommend  our  own 

Audio  Note  (UK) 

range  of  interconnects  and  loudspeaker 

cables. For further information, please consult your nearest Audio Note (UK) dealer, 
or alternatively please feel free to contact us directly.

 

 
 
 
 
 
 
 
 
 
 
 

Содержание AN-J















Отзывы: