background image

 
 

 

Once all the connections are completed and checked, ensure that the volume control 
for  your  amplifier  is  at  the  minimum  setting.  Connect  your  amplifier  to  the  mains 
supply,  and  make  sure  all  source  components  are  switched  on  BEFORE  the 
amplifier; to protect you

ʼ

re AN-E loudspeakers from damage, always make sure the 

amplifier  is  the  LAST  piece  of  equipment  to  be  switched  on  and  the  FIRST  to  be 
switched off. 
 

Bedding in

 

 

While we fully expect your AN-E

 

loudspeakers to produce  

 

 

 

beautiful music, they may not do so from the first moment out 

 

 

 

of the box. Don

ʼ

t be alarmed; this is perfectly normal. 

Dynamic  loudspeakers  have  a  running  in  period,  during  which 
time  the  drive  units  “loosen  up”.  During  this  period,  the  sound 
may  be  somewhat  dry,  bright  and  constricted.  As  the 
suspension and cone materials of both drive units “softens up”, 
the  fullness  of  the  bass  and  the  smoothness  of  the  treble  will 
start  to  emerge  and  the  true  sound  of  the  AN-E  will  be 
revealed. 
We expect the AN-E to have a running in period of around 100 
hours,  which  for  the  average  listener  will  take  about  a  month, 
based  on  three  hours  of  listening  per  day.  This  period  can 
however vary considerably due to factors such as music types, 
listening  volume  and  type  of  amplification  used.  (Loud  heavy 
metal or Mahler symphonies are especially effective!) 

 

 

 

If the rest of your system is of commensurate quality, you may 
notice  that  when  you  haven

ʼ

t  played  your  AN-E

 

for  a  week  or 

longer,  they  seem  to  experience  a  lesser  version  of  this 
running-in process again. Everything will be completely back to 
normal within 5 to 10 hours. 

 

Cleaning   

 

No  special  maintenance  is  required  for  your  AN-E 
loudspeakers.  Use  a  soft,  clean  lint  free  cloth  to  remove  any 
surface  marks  from  the  cabinets.  For  finger  marks  /  grease, 
use  a  soft,  clean  lint  free  cloth,  very  lightly  moistened  with  a 
solution  of  warm  water  and  mild  detergent.  Do  not  use  any 
alcohol  or  solvent  based  cleaning  products,  as  they  may 
damage the finish of the cabinet. 

 

 

 

 

Under  no  circumstances  should  you  attempt  to  clean  the 
drive units of your loudspeaker. 

 
 

 

 

Playing  some  loud  music  will  displace  any  dust  that  has 
collected on the drive units! 

 
 
 
 
 

OPERATION 

Содержание AN-E SEC Signature















Отзывы: