manualshive.com logo in svg

Audinate Dante MY16-AUD, Руководство пользователя, Страница: 17 / 58

Поделиться
Скачать
Audinate Dante MY16-AUD Скачать руководство пользователя страница 17

Dante-MY16-AUD2 User Guide

Copyright © 2016 Audinate Pty Ltd. All rights reserved.

-17-

Installing Your Card

Before you install

Before you install the Dante-MY16-AUD2 card, you should note down the last 6 characters of the MAC
address of the card.

This is printed on a label on the card itself. The last six characters of the MAC address of the card are used
in the default device name.

e.g.: Dante-MY16-AUD2 card with MAC address 00:1D:C1:03:01:C4 will show as

MY16-2-0301C4

in Dante Controller until it is given a more suitable name.

If you are installing more than one card, this will allow you to easily identify which card you have installed in
which slot when viewing them on Dante Controller in order to configure or rename them appropriately.

To Install

To install your Dante-MY16-AUD2 card in your chosen compatible Yamaha equipment, please carefully
follow the instructions below. For instructions relating to specific Yamaha equipment, please refer to the
Manual for that equipment.

Important:

Please observe normal antistatic precautions when handling sensitive electronic

equipment to avoid damage.

1. Check that your Yamaha equipment has a compatible, empty MY16 slot.

2. Turn off the power to your Yamaha equipment

3. Remove the screws from the cover of the empty MY16 slot.

4. Store the blank slot cover and its screws in a safe place for later use.

5. Remove the Dante-MY16-AUD2 from its anti-static bag.

6. Carefully slide the Dante-MY16-AUD2 card into the slot, ensuring the card is sitting within the guide

rails.

7. After checking the card is within the guide rails, fully install the card by pushing it firmly until the face-

plate is flush with the back of the Yamaha equipment.

8. Screw the thumbscrews into place.

Содержание Dante MY16-AUD



























































Отзывы:

Нет отзывов