manualshive.com logo in svg

Audi Q5 80A 2017, Руководство по установке, Страница: 23 / 26

Поделиться
Скачать
Audi Q5 80A 2017 Скачать руководство пользователя страница 23

– Press heat shield -1- towards the cross panel, insert bolts

-arrows- and tighten to a torque of 2.5 Nm.

 Note

Make sure the retrofit wiring harness moves freely.

8.4

Connecting the supply line for the

brake booster

WARNING

There are two variants for the position of the brake boos-
ter supply line.

Variant 1: Up to VIN no. WA1BNAFY8J2000552, the on-
board supply wire for the brake booster is located under
the convenience system central control unit -J393-.

Variant 2: From VIN no. WA1BNAFY8J2000552, the on-
board supply wire for the brake booster is integrated in
the main wiring harness above the fuse holder.

8.4.1  Workflow for variant 1

– Loosen fastener -2- and pull fuse holder -1- upwards slightly.

Detach fuse holder -1- from the tabs -3- and remove it upwards
-in the direction of the arrow-.

Place the fuse holder -1- to one side.

 Note

The electrical wires remain connected.

Installation instructions - Audi Q5 (80A) 2017 ► Fixed/mechanically removable towing

bracket with E-set (NAR),

Edition 01

8  Electrical connection

19

Содержание Q5 80A 2017



























Отзывы:

Нет отзывов