Audi 8T8.071.126.A Скачать руководство пользователя страница 6

Audi A5 Sportback (8T) 2010

 

 

No. 122, Body, Edition 8.09

2  Safety notes

6

4

WARNING!

All bolt connections and connections for the roof bars and 

for the add-on components must be checked prior to     

travelling to ensure they are positioned and installed       

correctly. Tighten if necessary.

Recheck bolted connections and connections at appropriate 

intervals and tighten if necessary. The bolted connections 

and connections must be checked at short intervals if   

travelling on a poor stretch of road.

If this guideline is not observed, this can result in the roof 

bars or the add-on components becoming loose or falling 

off — risk of accident!

WARNING!

For the safety of other road-users, the roof bars and any 

add-on components must be removed from the vehicle 

when they are not being used.

WARNING!

Repairs or the replacement of parts must only be performed 

by a qualified workshop. It is recommended that genuine 

spare parts available from your Audi partner are used.

Caution!

The height of the vehicle will change due to the installation 

of the roof bars with/without add-on components. Please pay 

attention to this when entering garages, driving through   

tunnels, underpasses etc.

Caution!

Do not enter a car wash with roof bars with/without add-on 

components installed.

Содержание 8T8.071.126.A
















Отзывы: