manualshive.com logo in svg

AuCom CSX-007, Руководство по обслуживанию, Страница: 9 / 22

Поделиться
Скачать
AuCom CSX-007 Скачать руководство пользователя страница 9

AVOIDING DAMAGE 

    

 

 

 

 

 

Page 8 

CSX Series 

710-02696-00C 

 

 

1  Soft starter output relay 
2  Slave relay coil 
3  Contactor coil 

 

 

 

2.

 

If the contactor has a volt free electronic input (low voltage/low current), the soft starter's output relay can be 

wired directly into this input for contactor control. 

 

 

1  Soft starter output relay 
2  Contactor coil 

 

 

 

 

3.3

 

Control Inputs 

CSX Series soft starters can be operated by external two wire or three wire control signals.  External switches are 

configured and wired into control input terminals 01, 02. 

 

•

 

External switches operating the control inputs must be rated for the control voltage being used and a 
continuous current of 100 mA. 

•

 

Incorrect configuration and wiring of the external contacts/switches to the control input terminals may cause 
damage. 

•

 

If long cable runs are used, wiring must be twisted pair or shielded cable and must be separated from AC 
power cables by at least 300 mm. 

 

 

 

NOTE 

Applying voltage to the control inputs will damage the soft starter.  Damage to the control inputs is not 
covered by warranty.  

 

Содержание CSX-007























Отзывы:

Нет отзывов