AUBER INSTRUMENTS
WWW.AUBERINS.COM
2013.05
P2/2
Buzzer on
Buzzer on
PV
PV
Figure 4. Absolute high alarm
Figure 5. Absolute low alarm
5.2 System Configuration Parameters
(accessed by code 0089)
Table 3. System configuration parameter setting
PSb
0
rd
1
CorF
0:
° C 1:° F
End
Code
Setting Range
Initial
Note
Inty
K
outy
3
inty
Atdu
Hy
1
Description
outy
hy
atdu
psb
rd
corf
end
Input Sensor Type
Output Mode
Hysteresis Band
Ignore this setting
Input Offset
External alarm type
Display Unit
Exit
See Appendix
0, 1, 2, 3, 4, 5, 6
0~9999
0~200
-1000~1000
0: low 1: high
1
Note 3
Note 4
Note 6
Note 7
Figure 6. The system setup flow chart
Note 3
. The value of outy should be 3.
Note 4
. The default setting for the external buzzer is high limit alarm. The external
b u z z er w i l l be on when the tempeature is above SV+Hy will be off when the
temperature drops back to SV. The default setting for the Hy is 1.
Note 2. Set alarm for internal buzzer
The meter offers two alarms that can be set to turn on the internal buzzer at specific
temperatures. The first alarm is controlled by parameters AH1 and AL1. The initial
setting will turn on the buzzer at 481 ° F and off when temperature drops below 480° F.
The second alarm is controlled by parameters AH2 and AL2. The initial setting of the
second alarm is deactivated. It can be set as low alarm to send warning.
AH1 and AH2 are the temperatures to turn the inernal buzzer on; AL1 and AL2 are the
temperatures to turn buzzer off. When AH1(2) >AL1(2), the alarm is set for absolute
high alarm as shown in Figure 4 below. When AH1(2) <AL1(2), the alarm is set for
absolute low alarm as shown in Figure 5 below. When AH1(2)=AL1(2), the alarm is
deactivated.
Example, if AH1=481, AL1=480, when the temperature goes up to 481° F, the buzzer
will be on; when the temperature drops down to 480° F, the buzzer will be off. If
AH2=180, AL2=185, when the temperature drops down to 180° F, the buzzer will be
on; when the temperature goes up to 185° F, the buzzer will be off.
User can press the shift key (>) to temporarily mute the buzzer sound. The alarm will
buzz again if the alarm set temperature is reached again. To permanently deactivate
the alarm, set AH1=AL1 or AH2=AL2. Please see flow chart in Figure 3 on how to set
the value.
The default setting is both internal and external buzzer are on when the
temperature is above 481 (SV+Hy, AH1); will be off when the temperature drops
down to 480 (SV, AL1).
Operation Mode
0089
Enter Code
Parameter Display
Output mode selection
inty
X
XXXX
X
XXXX
outy
atdu
psb
Hysteresis Band
Input offset
SET
SET
SET
SET
SET
SET
SET
X
rd
Heating/Cooling
SET
X
corf
Display Unit(C/F)
end
SET
SET
SET
SET
SET
XXXX
HY
SET
Autotune offset
SET
Note 5
Note 5
. Calibration offset, PSb is used to set an input offset to compensate the error
produced by the sensor. For example, if the meter displays 5 º C when probe is in
ice/water mixture, setting PSb= -5, will make the controller display 0 ºC.
Note 6
. Rd is for system function selection, Its value should be kept as 1 for high limit
alarm.
Note 7.
Display unit selection CorF: 0 for Celsius (° C); 1 for Fahrenheit (° F).
Auber Instruments, Inc
5755 North Point Parkway, Suite 99
Alpharetta, GA 30022 USA
Tech support: 770-569-8420, 404-983-8228
Copyright 2007-2016, Auber Instruments All Rights Reserved.
No part of this manual shall be copied, reproduced, or transmitted in any way
without the prior, written consent of Auber Instruments. Auber Instruments
retains the exclusive rights to all information included in this document.
Additional note:
The remote alarm control output of this thermometer can also be used as a PID or
on/off control output. For details, please refer to Auber SYL-1614 manual.
