TI033
400-033-001-C 30/11/06 1/2
TI033
Installation and User Guide
Programmable Wall Switch
The TI033 programmable wall switch has been designed to control
lightings and motors:
NOTE
: This switch cannot be used if there are not at least 2 white
wires joined by a connector inside the electrical box.
n
Cut power at the circuit breaker to avoid electric shock.
o
Remove the existing switch.
p
Install the new switch as shown in the diagram below.
q
Apply power at the circuit breaker.
n
Pry the switch door open from the
bottom using a small screwdriver.
o
Ensure the
ON/OFF
selector is set
to ON.
p
Reset the switch using a paper clip.
0:00
and
MO
will flash.
If the display is blank:
•
Ensure the
ON/OFF
selector is properly engaged in the
ON
posi-
tion. Push it to the right using a small screwdriver.
NOTE
: The switch displays the time in 24-hour format by default or
following a reset.
n
To change to 12-hour format (or vice versa), proceed as follows:
a) Press one of the control buttons to ensure the
MAN
or
AUTO
indicator is displayed.
b) Press the
MIN
and
HOUR
buttons simultaneously and brief-
tly (
0:00
display = 24-hour,
12:00
display = 12-hour ).
o
Set the time using the
HOUR
and
MIN
buttons. If you have
selected the 12-hour format, ensure that
PM
appears on the
screen when an afternoon time is displayed.
p
Set the day by using the
DAY
button.
q
Press one of the control buttons or close the switch door to
return to normal operation.
The programmable switch has 2 operating modes: manual (
MAN
)
and automatic (
AUTO
). To switch mode, press the switch door for 3
seconds.
Manual Mode
The programmable switch operates as a regular
switch. Briefly press the switch door to turn the lights
On or Off. The mode (
MAN
)
and state (
ON
or
OFF
)
are displayed.
Automatic Mode
The programmable switch follows the programmed
schedule. The mode (
AUTO
), state (
ON
or
OFF
)
and current program number are displayed.
To temporarily override the programmed schedule,
briefly press the switch door. The new state
(
ON
or
OFF
)
will flash to
show that this state is temporary. The override remains in effect until
you press the switch door again or until the beginning of the next
program.
You can set up to 7 programs. To set a program, you need to enter its
start time (
ON
) and its end time (
OFF
).
n
Pry the switch door open using a small screwdriver.
o
Press the
PGM
button to display a program and
its On or Off time. For example, when you first
press
PGM,
program number 1 (
P1
) and its On
time (
ON
) will appear.
- : - -
will appear instead
of the time if the program is not set (inactive).
p
Press the
DAY
button to select the day to which
you want to apply the program.
NOTE
: If you want to apply the program to
every day of the week, press
DAY
until all the
days are displayed. (This still counts as 1 program, not 7)
n
Applications
1.
Load type
Maximum load Examples
Resistive load
2400 W
(20 A @ 120 V)
•
incandescent lights
•
halogen lights
•
block heater
Inductive load
2400 W
(20 A @ 120 V)
•
fluorescent lights
•
compact fluorescent lights (CFL)
•
sodium lamps
•
electronic ballasts
Motor
1 hp
•
pool filter pumps
•
fans
o
Installation
2.
p
Power-On
3.
120 VAC
white (neutral)
black (line)
white
black
white
black
blue
Control (4)
Reset
On/Off
selector
q
Setting the Clock
4.
r
Selecting the Operating Mode
5.
s
Programming
6.
400-033-001-C ENG (print at 90%).fm Page 1 Thursday, November 30, 2006 8:50 AM
