ATS SuperTrak GEN3 Скачать руководство пользователя страница 260

Страница: 260 / 366

248

SuperTrak™ GEN3 System Operation and Maintenance Manual

Rev. 9 (12-2021)

Maintenance

Clean a Pallet Encoder Strip

1. Gently wipe the encoder strip with a soft, dry, clean cloth.

2. Inspect the encoder strip, to make sure it is not damaged.

See

Inspect a Pallet Encoder Strip

on page 248.

Inspect a Pallet Encoder Strip

Inspect the encoder strip with magnetic viewing film, to verify that the poles
appear correctly.

Each pole should be vertical to one another. If the poles appear damaged, replace
the encoder strip.

Never use a magnet to clean the encoder strip. Contact with magnetic
material will cause permanent damage to the magnetic encoder strip.

Содержание SuperTrak GEN3















































































































































































































































































































































































Результаты поиска

Содержание SuperTrak GEN3

Отзывы:

ATS SuperTrak GEN3, Руководство по эксплуатации и обслуживанию, Страница: 260 / 366

Результаты поиска

Содержание SuperTrak GEN3

Отзывы: