ATS SuperTrak GEN3 Скачать руководство пользователя страница 258

Страница: 258 / 366

246

SuperTrak™ GEN3 System Operation and Maintenance Manual

Rev. 9 (12-2021)

Maintenance

Electrical Enclosure

Pallets

Monthly

Inspect

Inspect each pallet for wear.
See

Inspect a Pallet

on page 195.

Monthly, or as
determined
for your
application

Lubricate

Add lubricant to the pallet.
See

Lubricate the Pallet Lubrication

Felt

on page 250.

Monthly

Clean

• Clean the pallet body. Wipe off

debris using a clean, soft, cloth.

• Clean the magnet assembly. Wipe

metal debris to a corner or edge of
the magnet and then pull it off.

• Clean the pallet encoder strip. See

Clean a Pallet Encoder Strip

page 248.

Power supply

Monthly

Inspect

Inspect the air filter for dirt and debris.
If required, replace the filter.
See

Replace a Power Supply Filter

page 249.

Table and
Supporting
Structure

Weekly

Clean

Clean off debris, using a clean, soft
cloth.

Component

Frequency

Task

Description

Fan

Monthly

Inspect

Inspect for damage and loose
connections. If required, repair or
replace.

As Required

Clean

Clean off debris, using a clean, soft
cloth.

Filter

Monthly

Inspect

Inspect the condition of the filter. If
required, vacuum, wash or replace.
See

Clean a Control Panel Air Filter

page 247.

Component

Frequency

Task

Description

Содержание SuperTrak GEN3















































































































































































































































































































































































Результаты поиска

Содержание SuperTrak GEN3

Отзывы:

ATS SuperTrak GEN3, Руководство по эксплуатации и обслуживанию, Страница: 258 / 366

Результаты поиска

Содержание SuperTrak GEN3

Отзывы: