ATS SuperTrak GEN3 Скачать руководство пользователя страница 179

Страница: 179 / 366

Technician Procedures

SuperTrak™ GEN3 System Operation and Maintenance Manual

167

Rev. 9 (12-2021)

Install an Encoder Assembly - Straight and Curved Sections

Power to the controller and gateways should OFF while installing encoders, and
then turned ON before calibration.

1. If required, remove the old encoder assembly.

See

Remove an Encoder Assembly - Straight Section

on page 165.

See

Remove an Encoder Assembly - Curved Sections

on page 166.

2. Connect the RJ11 plug to the new encoder assembly connection.

3. Align the encoder assembly with the locating dowels.

4. To prevent damage to the RJ11 connection, make sure it is aligned with the

RJ11 opening.

5. Press the encoder assembly firmly down onto the locating dowels.

6. Secure the encoder assembly in position with five (5) screws.

7. Install an encoder assembly screw cap over each of the five (5) screws.

8. Remove locks and tags.

9. Turn the

SuperTrak conveyance platform power disconnect switch

the ON position.

10. Calibrate the motor with the new encoder assembly.

See the TrakMaster built-in help for the calibration procedure.

11. If the straight section has a pallet setup stationary mount installed, reference

the encoder positions.

See

Reference the Encoder Position

on page 225.

Содержание SuperTrak GEN3















































































































































































































































































































































































Результаты поиска

Содержание SuperTrak GEN3

Отзывы:

ATS SuperTrak GEN3, Руководство по эксплуатации и обслуживанию, Страница: 179 / 366

Результаты поиска

Содержание SuperTrak GEN3

Отзывы: