manualshive.com logo in svg

ATS SuperTrak GEN3, Руководство по эксплуатации и обслуживанию, Страница: 177 / 366

Поделиться
Скачать
ATS SuperTrak GEN3 Скачать руководство пользователя страница 177

   Technician Procedures

SuperTrak™ GEN3 System Operation and Maintenance Manual

165

Rev. 9 (12-2021)

Replace an Encoder Assembly

A 180 deg. (800 mm) section has four (4) encoder assemblies, while all other 
curved and straight sections have two (2) encoder assemblies. Replace the 
encoder assembly if a SuperTrak conveyance platform fault indicates that 
replacement is required.

Remove an Encoder Assembly - Straight Section

1. Turn the 

SuperTrak conveyance platform power disconnect switch 

to 

the OFF position.

2. Lock out and tag hazardous energy.

See 

Lockout and Tagout Locations

 on page 12.

3. Remove the five (5) encoder assembly screw caps.

4. Remove the five (5) encoder assembly screws.

5. Lift the encoder assembly straight up, off the two locating dowels.

6. Disconnect the RJ11 plug from the 

encoder assembly connection.

Содержание SuperTrak GEN3















































































































































































































































































































































































Отзывы:

Нет отзывов