ATS SuperTrak GEN3 Скачать руководство пользователя страница 128 | Manualshive

Страница: 128 / 366

ATS SuperTrak GEN3 Скачать руководство пользователя страница 128

116

SuperTrak™ GEN3 System Operation and Maintenance Manual

Rev. 9 (12-2021)

Controls and Connections

Connections

This section describes the following SuperTrak conveyance platform connections:

•

Straight Section to Straight Section Connections

•

Straight Section to 180 Deg. Section Connections

•

180 Deg. Section (500 mm) to SuperTrak Control Panel Connection

•

Ethernet Port Connection

•

Main Power Connection

•

Safety Circuit Connection

•

PLC Connection

•

Ethernet POWERLINK Connection

•

Gateway Network Connections

Straight Section to Straight Section Connections

Replace an Electrical Interconnect

Straight Section to 180 Deg. Section Connections

If required, remove the existing electrical interconnect as described above.

180 Deg. Section (500 mm) to SuperTrak Control Panel
Connection

Install an Electrical Interconnect Between a Curved Section and a SuperTrak

Control Panel

Connection information provided in this section is based on the use of the
ATS SuperTrak control panel. The control panel meets UL certification and
product testing. If an alternate electrical panel is used, it must meet the
guidelines defined in the

SuperTrak GEN3 Design Considerations

document.

«
...
126
127
128
129
130
...
»

Содержание SuperTrak GEN3















































































































































































































































































































































































Отзывы:

Нет отзывов