Atracsys fusionTrack 500 Скачать руководство пользователя страница 40

Страница: 40 / 114

User manual

Version: v4.5.2

For single-use

markers

, the end user manual must clearly

state that the

markers

should not be reprocessed. The

markers

packaging must be marked with a label indicating

they cannot be reprocessed.

For single-use

fiducials

, instructions about replacing new

fiducials

after every (single) use must be clearly specified by

the integrator in the end user manual. Packages of passive

fiducials

have to be marked with a label indicating that they

cannot be reprocessed.

A passive fiducial could be damaged due to a shock /
scratch of the reflecting material. Instructions about not us-
ing deteriorated

fiducials

and how to replace a deteriorated

passive

fiducial

must be clearly specified by the integrator in

the end user manual.

Integrator has to specify in the end user manual instructions
how to screw / plug

fiducials

markers

7.6.2 Active markers

The active

markers

consist of IR-LEDs mounted in a rigid structure. The LEDs can either emit continuously

or be synchronised with the fusionTrack cameras. In the latter case, the

marker

also contains an IR receiver.

An active

marker

is powered by a battery, or from the equipment to which it is attached. Those

markers

can either be wired or wireless.

The fusionTrack device IR communication sends a pattern which is recognised by the IR receiver of

the active

marker

. Once the IR pulse is detected by the

marker

, the

marker

emits IR radiations, which is

detected by the fusionTrack device.

Active

marker

electronics has to be completely sealed in or-

der to avoid liquid penetration due to cleaning. The inte-
grator has to indicate in the end user manual instructions to
clean active

markers

. The integrator has to specify in the

end user manual that the operability verification procedure
(see Chapter 12) must be done after each cleaning.

A geometrically deformed active

marker

due to a manufac-

turing defect could lead to wrong measurements causing
patient injury. The integrator has to perform individual test-
ing during

marker

calibration.

Atracsys / 2020-06-17 / 16:48:00

39 / 113

Содержание fusionTrack 500



















































































































Результаты поиска

Содержание fusionTrack 500

Отзывы:

Похожие инструкции для fusionTrack 500

Бренды по названию

Популярные бренды

Atracsys fusionTrack 500, Руководство пользователя

Результаты поиска

Содержание fusionTrack 500

Отзывы:

Похожие инструкции для fusionTrack 500

Бренды по названию

Популярные бренды