LED
Color
State
Description
P
W
R1/
P
W
R2
Green
O
n
Power is supplied from P
W
R1/P
W
R2
O
ff
No power input detected from P
W
R1/P
W
R2
A
LM
Red
O
n
Alarm is triggered
b
y user defined e
v
ents
O
ff
Alarm is not triggered
b
y user defined
events
RUN
Green
Blinking
AP firmware is running normally
O
ff
System is not ready or halt
Ring
Green
O
n
All rings in normal condition or
CC
hain in
normal condition
Blinking
Ring in protection state or a port is link down
in
CC
hain
O
ff
Ring is disa
b
led or
CC
hain is disa
b
le
R.
M
Green
O
n
T
he de
v
ice is a
M
aster of the
E
RPS Ring or
iA-Ring or a Head of CChain
Blinking
T
he de
v
ice is a
T
ail of
CC
hain
O
ff
T
he de
v
ice is a Sla
v
e of the
E
RPS Ring or
i
A-
Ring or a
M
em
b
er of
CC
hain
10G
O
n
LED
Panel
Green
O
n
Port is linked
Blinking
D
ata is transmitting on this port
O
ff
No data is transmitting
L
AN
Am
b
er
O
n
E
thernet is linked at 1000
Mb
ps
Blinking
E
thernet is linked at 100
Mb
ps
O
ff
E
thernet is linked at 10
Mb
ps
Green
O
n
E
thernet is linked
Blinking
Ethernet is active and data is being transmitted
O
ff
E
thernet is not linked
S
F
P
(
1G
)
Am
b
er
O
n
E
thernet is linked at 1000
Mb
ps
Blinking
E
thernet is linked at 100
Mb
ps
O
ff
E
thernet is linked at 10
Mb
ps
Green
O
n
E
thernet is linked
Blinking
Ethernet is active and data is being transmitted
O
ff
E
thernet is not linked
S
F
P
PoE
MACsec
(
10G
)
Am
b
er
O
n
E
thernet is linked at
10GMbps
Blinking
E
thernet is linked at 10
00Mbps
O
ff
E
thernet is linked at 1
00Mbps
Green
O
n
E
thernet is linked
Blinking
Ethernet is active and data is being transmitted
O
ff
Ethernet is not linked
Amber
O
n
Power is being supplied to a Powered
Device (PD)
O
ff
Power is not supplied to a Powered Device(PD)
Blue
O
n
MACsec active on that port
Blinking
Ethernet is active and data is being transmitted
O
ff
Ethernet is not linked
If the device requires servicing of any kind, you may need to disconnect and
remove it from its mounting. The initial installation should be done in a way that
makes this as convenient as possible.
■ Voltage/Power lines should be properly insulated as well as other cables. Be
careful when handing the so as to not trip over
■ Do not under any circumstance insert foreign objects of any kind into the heat
dissipation holes located in the different faces of the device. This may not only
harm the internal layout but might cause harm to you as well.
■ Do not under any circumstance open the device for any reason. Please
contact your dealer for any repair needed or follow the instructions on section
of your User’s Manual.
Field Maintenance and Service
Attention
1. It is recommend to use at least a 20 AWG cable for the AC power input.
It is suggested the cable to be resistant to at least 85°C temperature on the
power connector.
2. If the equipment is used in a manner not specified by the manufacturer, the
protection provided by the equipment may not be impaired.
3. Clean the device with dry or humid (water) soft cloth.
4. Before powering on the device, the Functional Ground (Grounding Screw)
shall be connected to the ground.
5. If the device is AC please connect PWR1. If AC redundant, connect PWR1
and PWR2 to the 100~240V AC power source. This power input manages
the full device functions except from PoE.
6. If the device is DC powered, please connect DC1 and DC2 to the DC
power supply.
7. If PoE is going to be used, also POE PWR1 and POE PWR2 should be
connected to 48~57 VDC power supplies). In order to avoid overheat and
damages to the internal components the user should follow the below
guidelines:
■ Total PoE power needed is <= 360W: connect to either power supply
■
POE PWR1 or POE PWR2 or both.
■ Total PoE power needed is >360W but <=720W (max): connect to both
■
POE PWR1 and POE PWR2 in order to avoid overhead.
8. POE PWR1 or POE PWR2 support maximum input 360 W.
9. POE PWR1 / POE PWR2 , + / - pins should be connected in same PWR input
Terminal block, please don’t cross-connect.
Environmental Limits
■ Operating Tem perature: -40 to 75°C (-40 to 167°F)
■ Storage Temperature: -40 to 85°C (-40 to 185°F)
■ Ambient Relative Humidity: 5 to 95%, 55°C (non-condensing)
■ Altitude: up to 2,000 m
■ Housing Protection : IP 30
Front View
Back View
Top View
Site View
482,6
6
464,5
31,8
440
340
44
Customers shall always obtain an authorized "RMA" number from Atop before
shipping the goods to be repaired to Atop. When in normal use, a sold product
shall be replaced with a new one within 3 months after purchase. The shipping
cost from the customer to Atop will be reimbursed by Atop.
After 3 months and still within the warranty period, it is up to Atop whether to
replace the unit with a new one; normally, as long as a product is under warranty,
all parts and labor are free of charge to the customers.
After the warranty period, the customer shall cover the cost for parts and
labor.Three months after purchase, the shipping cost from the customer to Atop
will not be reimbursed, but the shipping cost from Atop to the customer will be
paid by Atop.
Atop shall not be held responsible for any consequential losses from using Atop’s
product.
Warranty Policy
The warranty certification will not be effective until an authorized stamp issued by
Atop’s overseas agents.
Purchase Date: / / (yyyy/mm/dd)
Serial Number
Product Categories
Warranty
Warranty
Product Categories
Media Converters
Embedded Device Servers
Ethernet Switches
Wireless
Serial Device Servers
Modbus Gateways
DIN-Rail Power Supplies
Power Adaptors
Antennas
Other Accessories
Warranty Conditions
RMA and Shipping Costs Reimbursement
Limited Liability
1. Please contact your local dealers or Atop Technical Support Center at the
following numbers.
+ 886-3-550-8137 (Atop Taiwan)
+ 86-21-6495-6232 (Atop China)
2. Please report the defected problems via Atop’s Web site or E-mail account
Web Site
：
www.atop.com.tw, e-mail
：
Web Site
：
www.atop.com.cn, e-mail
：
3. Company Addr: 2F, No. 146, Sec. 1, Tung-Hsing Rd., Jubei, Hsinchu 30261,
Taiwan, R.O.C.
Manufacturer Addr: 1st FL 30 R&D RD II,SCIENCE-BASED INDUSTRIAL
PARK,HSINCHU 300 TAIWAN, R.O.C
Atop Customer Services and Supports
Products supplied by Atop Technologies are covered in this warranty for
sub-standard performance or defective workmanship. The warranty is not,
however, extended to goods damaged in the following circumstances:
(a) Excessive forces or impacts
(b) War or an Act of God: wind storm, fire, flood, electric shock, earthquake
(c) Use of unqualified power supply, connectors, or unauthorized parts/kits
(d) Replacement with unauthorized parts
Warranty Period
─ Any changes to this material will be announced on Atop website. ─
