background image

ATOMIC AMPS REACTOR 50/50 MANUAL 

13 

 

be the responsibility of Atomic Amplifiers. Atomic Amplifiers MUST perform 
all warranty services. Transportation charges involved in warranty services 
are the sole responsibility of the purchaser. 

A copy of the original sales receipt or packing slip must accompany all 
products being presented to an Atomic Amplifiers Authorized Service 
Center for warranty service. All products being returned to Atomic 
Amplifiers for warranty service must be accompanied by a copy of the 
original sales receipt or packing slip, a detailed description as to needed 
repairs, and an Atomic Amplifiers Return Authorization number. Atomic 
Amplifiers reserves the right to repair or replace the affected piece of 
equipment at their option but it is understood that repair or replacement 
as provided under this limited warranty is the sole and exclusive remedy to 
the purchaser for defective or non-conforming products. 

Atomic Amplifiers will not be held liable for any incidental consequential, 
special, punitive, or exemplary damages resulting from any defect or failure 
of this product other than the repair of the Atomic Amplifiers product 
subject to the terms of this limited warranty. Any product repaired or 
replaced under this limited warranty will, itself, be warranted only for the 
remainder of the limited warranty period of the original product being 
repaired or replaced. Products used for dealer rental purposes shall be 
warranted from the date of the original invoice to dealer and if sold will be 
warranted only for the remainder of the limited warranty period of the 
original product. 

This warranty gives you specific legal rights, and you may have other rights 
which vary from state to state, and province to province, and to the extent 
required by law, any limited warranty shall be limited to the duration of this 
limited written warranty.  

OTHER THAN AS STATED ABOVE, ATOMIC AMPLIFIERS MAKES NO 
WARRANTIES EITHER WRITTEN, EXPRESSED, OR IMPLIED WITH RESPECT TO 
THE PRODUCT. THIS WARRANTY IS EXCLUSIVE, AND ATOMIC AMPLIFIERS 
MAKES NO OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING 
IMPLIED WARRANTIES OR MERCHANTABILITY OR FITNESS FOR ANY 
PARTICULAR PURPOSE, ALL OF WHICH WARRANTIES ARE HEREBY BEING 
DISCLAIMED. 

 

 

Содержание Reactor 50/50
















Отзывы: