5
English
English
6
System Operation
Quick User Controls Guide
Bodypack Transmitter
1. Audio input socket(3pin), can be connected to various
kind of lavalier microphone or head-set microphone.
2. Power switch: turn on/off the transmitter power supply.
3. Transmit antenna.
4. LCD screen.
5. Infrared frequency window
6. Cell box, for 2 x 1.5V battery
7. Battery cover
8.
INSTRUMENT CORD GT
cable—connects instrument’s audio output to TX input jack
9.
HEADMIC
Headworn microphone (choice of models)—connects to transmitter input jack
10.
LAVALIER MIC
Lavalier (lapel) microphone (choice of models)—connects to transmitter input jack
1
2
5
6
7
8
9
10
3
4
CH-005
1. Key functions and operations
1. Press the middle button "SET" can select menu and
confirm your Settings
2. Press "▲" "▼" button to select or adjust the current menu,
and then "SET" key set to store your settings.
3.Long press "▲" "▼" key to select frequency and channel
quickly
Receiver
OPERATION MENU OF LCD
Volume
Adjust the volume knobs the add or reduce the volume level.
Note:
Do not mount the receiver on a rack directly
above an amplifier or other source of high heat. This could
degrade the performance of. Always ensure adequate airflow
and heat dissipation in any rack configuration.
Installing Antennas
Install antennas by connecting the two
Antennas
included
with your system onto the two
RF Connectors
located on
the back of the receiver. The two antennas must be installed.
The optimal positions of the antennas are 45° from the
receiver and 90° from each other. For maximum range, it is
always best to maintain a line-of-sight (no obstructions)
between the receiver antennas and the transmitter at all
times whenever possible.
Powering the Receivers
To power the receivers, plug the supplied AC/DC
Power
Supply
adapter into the
DC Input Jack
on the back of the
receivers, then plug the adapter into an AC outlet.
Note:
Any 12-16VDC power source with 800mA minimum
capacity can also be used. To turn on, press down the
Power
Button
The
LCD Display
will light up. To turn off, press the
Power button up. The LCD will display “OFF” then the
backlight will turn off indicating the receivers are off.
Connect either the ¼”
Unbalanced SUM Line Out
or ¼”
each
Unbalanced Line Out
or each
XLR Balanced Mic
Outs
to your mixing board, effect, or amplifier inputs (See
Connecting the Audio Outputs section).
Connecting the Audio Outputs
The receiver has one
Unbalanced Audio SUM Out
adjustable line level audio output and two
Balanced
XLR Mic
Out
fixed level jacks and each works independently per
channel. The Unbalanced Audio Out is controlled
by volume
knobs
. For unbalanced output, plug a ¼” mono (Tip/Sleeve)
audio cable into the Unbalanced Audio Out jack and plug the
other end into your mixing board or amplifier. When using the
instrument transmitter system, connect the Unbalanced
Audio SUM Out directly to your instrument amp or preamp. At
maximum receiver volume setting, as indicated by the
Volume display, the system output is approxi4dB
higher than a direct cord-to-amp connection.
B. Getting into the operating menu
Display
Press the SET button to get into the standard display into the
operating menu. 2-3 seconds later, CHANNL or FRE QU
appears.
CHANNEL DISPLAY
Press the SET button and select the CHANNEL mode. This
menu shows the current channel.
Press the
▲/▼ button can change the channel, If you hold
down a button, the display cycles continuously. The “fast search”
function allows you to get fast and easily to your desired setting.
The new setting flashes on the display until it is stored, or the
transmitter will work at the previous channel.
2.LCD display
A.Infrared frequency
Press the “SET” button when the LCD display “IR-TX”,2-3
seconds later, transmitting the infrared frequency to the
transmitter.
FREQUENT DISPLAY
Press the SET button and select the FRE QU mode. This
menu shows the current frequency.
Press the ▲/▼ button to adjust the setting. By briefly
pressing the ▲/▼ buttons, the display jumps either forwards
or backw-ards to the next settin continuously. (Illustration: To
display whi-ch menu depend on the previous SET status.)
Press the ▲/▼ button can change the frequency, If you hold
down a button, the display cycles continuously, The
“fastsearch”function allows you to get fast and easily to your
desired setting. The new setting flashes on the display until it
to stored, or the tran-smitter will work at the previous
frequency.
Press the SET button to store the setting, orthe screen
flashing after 2-3 seconds indicating that the settings are not
available, the transmitter still work at previous setting.