background image

 

10 

Atmel AVR365 

8336A-AVR-03/12 

5 EVALUATION BOARD/KIT IMPORTANT NOTICE 

This evaluation board/kit is intended for use for 

FURTHER ENGINEERING, 

DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY. 

It is 

not a finished product and may not (yet) comply with some or any technical or legal 
requirements that are applicable to finished products, including, without limitation, 
directives regarding electromagnetic compatibility, recycling (WEEE), FCC, CE or UL 
(except as may be otherwise noted on the board/kit). Atmel supplied this board/kit 
“AS IS,” without any warranties, with all faults, at the buyer’s and further users’ sole 
risk. The user assumes all responsibility and liability for proper and safe handling of 
the goods. Further, the user indemnifies Atmel from all claims arising from the 
handling or use of the goods. Due to the open construction of the product, it is the 
user’s responsibility to take any and all appropriate precautions with regard to 
electrostatic discharge and any other technical or legal concerns. 

EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER 
USER NOR ATMEL SHALL BE LIABLE TO EACH OTHER FOR ANY INDIRECT, 
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. 

No license is granted under any patent right or other intellectual property right of 
Atmel covering or relating to any machine, process, or combination in which such 
Atmel products or services might be or are used. 

Mailing Address: Atmel Corporation, 2325 Orchard Parkway, San Jose, CA 95131 

 

Содержание AVR365












Отзывы: