Atmel ATtiny25 Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 196

background image

117

7598H–AVR–07/09

ATtiny25/45/85

18.5

Changing Channel or Reference Selection

The MUX3..0 and REFS2..0 bits in the ADMUX Register are single buffered through a tempo-
rary register to which the CPU has random access. This ensures that the channels and voltage
reference selection only takes place at a safe point during the conversion. The channel and volt-
age reference selection is continuously updated until a conversion is started. Once the
conversion starts, the channel and voltage reference selection is locked to ensure a sufficient
sampling time for the ADC. Continuous updating resumes in the last ADC clock cycle before the
conversion completes (ADIF in ADCSRA is set). Note that the conversion starts on the following
rising ADC clock edge after ADSC is written. The user is thus advised not to write new channel
or voltage reference selection values to ADMUX until one ADC clock cycle after ADSC is written.

If Auto Triggering is used, the exact time of the triggering event can be indeterministic. Special
care must be taken when updating the ADMUX Register, in order to control which conversion
will be affected by the new settings.

If both ADATE and ADEN is written to one, an interrupt event can occur at any time. If the
ADMUX Register is changed in this period, the user cannot tell if the next conversion is based
on the old or the new settings. ADMUX can be safely updated in the following ways:

a.

When ADATE or ADEN is cleared.

b.

During conversion, minimum one ADC clock cycle after the trigger event.

c.

After a conversion, before the Interrupt Flag used as trigger source is cleared.

When updating ADMUX in one of these conditions, the new settings will affect the next ADC
conversion.

18.5.1

ADC Input Channels

When changing channel selections, the user should observe the following guidelines to ensure
that the correct channel is selected:

In Single Conversion mode, always select the channel before starting the conversion. The chan-
nel selection may be changed one ADC clock cycle after writing one to ADSC. However, the
simplest method is to wait for the conversion to complete before changing the channel selection.

In Free Running mode, always select the channel before starting the first conversion. The chan-
nel selection may be changed one ADC clock cycle after writing one to ADSC. However, the
simplest method is to wait for the first conversion to complete, and then change the channel
selection. Since the next conversion has already started automatically, the next result will reflect
the previous channel selection. Subsequent conversions will reflect the new channel selection.

Table 18-1.

ADC Conversion Time

Condition

Sample & Hold (Cycles from
Start of Conversion)

Total Conversion Time

(Cycles)

First conversion

13.5

25

Normal conversions

1.5

13

Auto Triggered conversions

2

13.5

«
...
115
116
117
118
119
...
»

Содержание ATtiny25





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATtiny25

Бренд: NCR Страницы: 6

Бренд: ICP DAS USA Страницы: 166

Бренд: ICP DAS USA Страницы: 64

Tunnel Master Jr

Бренд: ICS Страницы: 83

Бренд: Rain Bird Страницы: 138

Бренд: Watlow Страницы: 20

Freedom Bridge FB3

Бренд: Identiv Страницы: 2

Бренд: Castell Страницы: 7

Бренд: Velp Scientifica Страницы: 24

Бренд: FAAC Страницы: 25

Бренд: Digi Страницы: 19

CY3250-PLC20QFN

Бренд: Cypress Страницы: 2

Бренд: HomeMatic Страницы: 68

Бренд: Oilon Страницы: 74

Бренд: Viking Electronics Страницы: 12

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 706

Бренд: Shimaden Страницы: 64

Бренд: F&F Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды