Atmel ATmega128 Скачать руководство пользователя страница 191 | Manualshive

Страница: 191 / 386

background image

191

2467S–AVR–07/09

ATmega128

Writing this bit to one enables the USARTn Transmitter. The Transmitter will override normal
port operation for the TxDn pin when enabled. The disabling of the Transmitter (writing TXENn
to zero) will not become effective until ongoing and pending transmissions are completed, i.e.,
when the Transmit Shift Register and transmit buffer register do not contain data to be transmit-
ted. When disabled, the transmitter will no longer override the TxDn port.

• Bit 2 – UCSZn2: Character Size

The UCSZn2 bits combined with the UCSZn1:0 bit in UCSRnC sets the number of data bits
(character size) in a frame the Receiver and Transmitter use.

• Bit 1 – RXB8n: Receive Data Bit 8

RXB8n is the ninth data bit of the received character when operating with serial frames with 9-
data bits. Must be read before reading the low bits from UDRn.

• Bit 0 – TXB8n: Transmit Data Bit 8

TXB8n is the 9th data bit in the character to be transmitted when operating with serial frames
with 9 data bits. Must be written before writing the low bits to UDRn.

USART Control and
Status Register C –
UCSRnC

Note that this register is not available in ATmega103 compatibility mode.

• Bit 7 – Reserved Bit

This bit is reserved for future use. For compatibility with future devices, these bit must be written
to zero when UCSRnC is written.

• Bit 6 – UMSELn: USART Mode Select

This bit selects between Asynchronous and Synchronous mode of operation.

• Bit 5:4 – UPMn1:0: Parity Mode

These bits enable and set type of parity generation and check. If enabled, the Transmitter will
automatically generate and send the parity of the transmitted data bits within each frame. The
Receiver will generate a parity value for the incoming data and compare it to the UPMn0 setting.
If a mismatch is detected, the UPEn flag in UCSRnA will be set.

Bit

7

6

5

4

3

2

1

0

–

UMSELn

UPMn1

UPMn0

USBSn

UCSZn1

UCSZn0

UCPOLn

UCSRnC

Read/Write

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

Initial Value

0

0

0

0

0

1

1

0

Table 77.

UMSELn Bit Settings

UMSELn

Mode

0

Asynchronous Operation

1

Synchronous Operation

Table 78.

UPMn Bits Settings

UPMn1

UPMn0

Parity Mode

0

0

Disabled

0

1

(Reserved)

1

0

Enabled, Even Parity

1

1

Enabled, Odd Parity

«
...
189
190
191
192
193
...
»

Содержание ATmega128



































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ATmega128

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 31

Бренд: NAiS Страницы: 199

Бренд: Panasonic Страницы: 38

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 179

Бренд: Panasonic Страницы: 23

Бренд: 3M Страницы: 34

Бренд: ICM Controls Страницы: 2

Бренд: ICM Controls Страницы: 2

Бренд: Maestra Страницы: 22

Бренд: L. G. B. Страницы: 2

Бренд: L-Acoustics Страницы: 36

Бренд: Olsberg Страницы: 68

Cutler-Hammer Jockey

Бренд: Eaton Страницы: 12

MultiLoad II EXL

Бренд: Toptech Страницы: 83

Бренд: Winbond Страницы: 85

SUNSAVER SS-10-12V

Бренд: Morningstar Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды